Dose–response relationship(Redirected from Dose response)
This article needs additional citations for verification. (August 2018) (Learn how and when to remove this template message)
The dose–response relationship, or exposure–response relationship, describes the change in effect on an organism caused by differing levels of exposure (or doses) to a stressor (usually a chemical) after a certain exposure time, or to a food. This may apply to individuals (e.g., the dose makes the poison: a small amount has no significant effect, a large amount is fatal), or to populations (e.g.: how many people or organisms are affected at different levels of exposure).
Although dose and exposure are often interchangeably used, in the area of clinical pharmacology (the study of drugs), the two names are separated. The former means dosage or amount of dose administered to a person, whereas the latter means the time-dependent concentration (often in the circulatory blood or plasma) or concentration-derived parameters such as AUC (area under the concentration curve) and Cmax (peak level of the concentration curve) of the drug after its administration.
Studying dose response, and developing dose–response models, is central to determining "safe", "hazardous" and (where relevant) beneficial levels and dosages for drugs, pollutants, foods, and other substances to which humans or other organisms are exposed. These conclusions are often the basis for public policy.
The U.S. Environmental Protection Agency has developed extensive guidance and reports on dose-response modeling and assessment, as well as software. The U.S. Food and Drug Administration also has guidance to elucidate dose-response relationships during drug development.
Dose–response relationships generally depend on the exposure time and exposure route (e.g., inhalation, dietary intake); quantifying the response after a different exposure time or for a different route leads to a different relationship and possibly different conclusions on the effects of the stressor under consideration. This limitation is caused by the complexity of biological systems and the often unknown biological processes operating between the external exposure and the adverse cellular or tissue response.
A dose–response curve is a simple X–Y graph relating the magnitude of a stressor (e.g. concentration of a pollutant, amount of a drug, temperature, intensity of radiation) to the response of the receptor (e.g. organism or population under study). The response may be a physiological or biochemical response, or even death (mortality), and thus can be counts (or proportion, e.g., mortality rate), ordered descriptive categories (e.g., severity of a lesion), or continuous measurements (e.g., blood pressure). A number of effects (or endpoints) can be studied, often at different organizational levels (e.g., population, whole animal, tissue, cell).
The measured dose (usually in milligrams, micrograms, or grams per kilogram of body-weight for oral exposures or milligrams per cubic meter of ambient air for inhalation exposures) is generally plotted on the X axis and the response is plotted on the Y axis. Other dose units include moles per body-weight, moles per animal, and for dermal exposure, moles per square centimeter. In some cases, it is the logarithm of the dose that is plotted on the X axis, and in such cases the curve is typically sigmoidal, with the steepest portion in the middle. Biologically based models using dose are preferred over the use of log(dose) because the latter can visually imply a threshold dose when in fact there is none.
The first point along the graph where a response above zero (or above the control response) is reached is usually referred to as a threshold-dose. For most beneficial or recreational drugs, the desired effects are found at doses slightly greater than the threshold dose. At higher doses, undesired side effects appear and grow stronger as the dose increases. The more potent a particular substance is, the steeper this curve will be. In quantitative situations, the Y-axis often is designated by percentages, which refer to the percentage of exposed individuals registering a standard response (which may be death, as in LD50). Such a curve is referred to as a quantal dose-response curve, distinguishing it from a graded dose-response curve, where response is continuous (either measured, or by judgment).
A commonly used dose-response curve is the EC50 curve, the half maximal effective concentration, where the EC50 point is defined as the inflection point of the curve.
Statistical analysis of dose-response curves may be performed by regression methods such as the probit model or logit model, or other methods such as the Spearman-Karber method. Empirical models based on nonlinear regression are usually preferred over the use of some transformation of the data that linearizes the dose-response relationship.
Problems with linear modelEdit
The concept of linear dose-response relationship, thresholds, and all-or-nothing responses may not apply to non-linear situations. A threshold model or linear no-threshold model may be more appropriate, depending on the circumstances. A recent critique of these models as they apply to endocrine disruptors argues for a substantial revision of testing and toxicological models at low doses.
- Crump, KS; Hoel, DG; Langley, CH; Peto, R (1976). "Fundamental carcinogenic processes and their implications for low dose risk assessment". Cancer Research. 36 (9 Part1): 2973–9. PMID 975067.
- Lockheed Martin (2009). Benchmark Dose Software (BMDS) Version 2.1 User's Manual Version 2.0 (PDF) (Draft ed.). Washington, DC: United States Environmental Protection Agency, Office of Environmental Information.
- Altshuler, B (1981). "Modeling of dose-response relationships". Environmental Health Perspectives. 42: 23–7. doi:10.1289/ehp.814223. PMC 1568781. PMID 7333256.
- Hamilton, MA; Russo, RC; Thurston, RV (1977). "Trimmed Spearman-Karber method for estimating median lethal concentrations in toxicity bioassays". Environmental Science & Technology. 11 (7): 714–9. doi:10.1021/es60130a004.
- Bates, Douglas M.; Watts, Donald G. (1988). Nonlinear Regression Analysis and its Applications. Wiley. p. 365. ISBN 9780471816430.
- G. Y. Di Veroli, C. Fornari, I. Goldlust, G. Mills, S. B. Koh, J. L. Bramhall, F. M. Richards, and D. I. Jodrell, “An automated fitting procedure and software for dose-response curves with multiphasic features,” Sci. Rep., vol. 5, p. 14701, 2015. http://www.nature.com/articles/srep14701
- Vandenberg, LN; Colborn, T; Hayes, TB; Heindel, JJ; et al. (2012). "Hormones and endocrine-disrupting chemicals: Low-dose effects and nonmonotonic dose responses". Endocrine Reviews. 33 (3): 378–455. doi:10.1210/er.2011-1050. PMC 3365860. PMID 22419778.
- The popular Dr Fit free Windows-64 software for dose response fitting
- Online Tool for ELISA Analysis
- Online IC50 Calculator
- Ecotoxmodels A website on mathematical models in ecotoxicology, with emphasis on toxicokinetic-toxicodynamic models
- CDD Vault, Example of Dose-Response Curve fitting software