BR Standard Class 3 2-6-0

The BR Standard Class 3 2-6-0 was a class of mixed traffic steam locomotive designed by Robert Riddles for British Railways. It was essentially a hybrid design, the chassis being closely based on and sharing a number of parts with the LMS Ivatt Class 4, and having a boiler derived from a GWR No.2 boiler as fitted to the GWR Large Prairie 2-6-2T and 5600 Class 0-6-2T tank engines.

BR Standard Class 3 2-6-0
A Standard Class 3 at Bogside Racecourse in 1961
Type and origin
Power typeSteam
DesignerRobert Riddles
BuilderBR Swindon Works
Build dateFebruary – September 1954
Total produced20
Specifications
Configuration:
 • Whyte2-6-0
 • UIC1′C h2
Gauge4 ft 8+12 in (1,435 mm) standard gauge
Leading dia.3 ft 0 in (0.914 m)
Driver dia.5 ft 3 in (1.600 m)
Length55 ft 11+14 in (17.05 m)
Width8 ft 5+58 in (2.58 m)
Height13 ft 0 in (3.96 m)
Axle load16.25 long tons (16.51 t; 18.20 short tons)
Adhesive weight48.5 long tons (49.3 t; 54.3 short tons)
Loco weight57.5 long tons (58.4 t; 64.4 short tons)
Tender weight42.15 long tons (42.83 t; 47.21 short tons)
Tender typeBR2A
Fuel typeCoal
Fuel capacity6 long tons (6.1 t; 6.7 short tons)
Water cap.3,500 imp gal (16,000 L; 4,200 US gal)
Firebox:
 • Grate area20.35 sq ft (1.891 m2)
BoilerBR6
Boiler pressure200 psi (1.38 MPa)
Heating surface:
 • Firebox118.42 sq ft (11.002 m2)
 • Tubes and flues923.54 sq ft (85.800 m2)
Superheater:
 • Heating area184.50 sq ft (17.141 m2)
CylindersTwo, outside
Cylinder size17.5 in × 26 in (444 mm × 660 mm)
Performance figures
Tractive effort21,490 lbf (95.6 kN)
Factor of adh.5.05
Career
OperatorsBritish Railways
Power class3MT
Numbers77000–77019
Axle load classRoute availability 4
Withdrawn1965–1967
DispositionAll scrapped

Design details

edit

The design and construction took place at the ex-Great Western Railway Swindon Works, along with the 2-6-2 tank engine version of the class, though some details were designed at Brighton, Derby and Doncaster.[1] Although the boiler shared flanged plates with the GWR No.2 boiler the barrel was shortened by 5+1316 inches and a dome added. Strangely the class did not share the same design of wheels as the Doncaster-designed BR Standard Class 4 2-6-0, however both shared the 5 ft 3 in (1,600 mm) driving wheels and the same piston stroke, and hence crank-pin throw.

In common with a number of the other BR Standard Classes, the chassis design used a number of LMS-designed components including Brake Hanger Brackets, Flexible Stretcher Brackets and Reversing Shaft Brackets.

The cylinder covers of engines as built were fitted with "screw-in" type pressure relief valves. From September 1955 revised cylinder covers were introduced for renewals incorporating "bolt-on" type pressure relief valves.[2]

Although the chassis had many almost identical parts to the LMS Ivatt Class 4 the motion brackets were derived from the design of those fitted to the LMS Ivatt Class 2 2-6-0 and LMS Ivatt Class 2 2-6-2T.

Unlike a number of the larger BR Standards the exhaust steam manifold within the smokebox saddle was a steel fabrication that was part of the welded saddle.[3] In a number of the large BR standards (BR Standard Class 6 and Class 7 engines) the exhaust steam manifold was a steel casting welded into the saddle during manufacture.[4]

Service

edit

Only 20 were built, numbers 77000–77019, all at Swindon Works. Due to their small number, the class were the antithesis of 'standard' engines and it would probably have been better to build more 2-6-0s to the Standard Class 4 and Standard Class 2 designs instead. None have survived to preservation, though some components were saved from scrapyards for use on a project to build a new Standard Class 3 2-6-2T. This class was the last class of steam locomotive on British Railways to remain complete before suffering its first withdrawal.[citation needed]

Operation

edit

Their operations were mainly restricted to the North Eastern and Scottish Regions, of British Railways, although 77014 ended its days on the Southern Region as it was transferred from Northwich depot on the London Midland Region to Guildford depot on the Southern Region in March 1966; it was withdrawn in July 1967.[5][6]

Other than this operation was in some more remote areas, such as 77011 which worked the Haltwhistle - Alston line from 1955.[7]

Withdrawal

edit
Withdrawals
Year Number in service
at start of year
Number withdrawn Locomotive numbers
1965 20 1 77010
1966 19 16 77000–01/03–09/11/13/15–19
1967 3 3 77002/12/14

References

edit

Citations

edit
  1. ^ Cooke, B.W.C., ed. (June 1954). "British Railways Standard Class "3" 2-6-0 Locomotives". The Railway Magazine. Vol. 100, no. 638. Westminster: Tothill Press. pp. 418–419.
  2. ^ Rear cylinder cover to BR drawing SL/SW/35 being superseded by SL/SW/666 and front cylinder cover to drawing SL/SW/85 being superseded by SL/SW/667 for renewals from September 1955.
  3. ^ Confirmed on original BR drawing SL/SW/616 sourced from the NRM
  4. ^ Confirmed on original BR drawing SL/DE/19620 sourced from the NRM
  5. ^ Teal (1985), p. 74.
  6. ^ Walford (2003), p. 226.
  7. ^ Wright, Ian L (1986). London & North Eastern. Branch Line Memories. Vol. 4. Truro: Atlantic Transport Publishers. p. 36. ISBN 0-906899-19-2.

References

edit
  • Teal, Paul (1985). BR Motive Power Allocations 1959-1968 - 1: BR Standards & Austerities. Shepperton: Ian Allan. ISBN 0-7110-1540-6.
  • Walford, John (2003). "Section 5.7.2 Allocation Summary". In Taylor, R.K. (ed.). A Detailed History of British Railways Standard Steam Locomotives. Vol. Two: The 4-6-0 and 2-6-0 Classes. Peterborough: RCTS. ISBN 0-901115-93-2.

Bibliography

edit
  • ABC of British Railways Locomotives. Vol. Part 3 (Winter 1962 ed.). Ian Allan. p. 175.
  • Bradley, Rodger P. (1984). The Standard Steam Locomotives of British Railways. David & Charles. ISBN 0715383841.
edit