The alveolar process (//) (also called the alveolar bone) is the thickened ridge of bone that contains the tooth sockets (dental alveoli) on the jaw bones that hold teeth. In humans, the tooth-bearing bones are the maxilla and the mandible. The curved part of each alveolar process on the jaw is called the alveolar arch.
Left maxilla. Outer surface. (Alveolar process visible at bottom.)
Cartilages of the nose, seen from below. (Alveolar process of maxilla visible at bottom.
|Anatomical terms of bone|
The alveolar process contains a region of compact bone adjacent to the periodontal ligament (PDL), called the lamina dura when viewed on radiographs. It is this part which is attached to the cementum of the roots by the periodontal ligament. It is uniformly radiopaque (or lighter). Integrity of the lamina dura is important when studying radiographs for pathological lesions.
The alveolar process has a supporting bone, both of which have the same components: fibers, cells, intercellular substances, nerves, blood vessels, and lymphatics.
The alveolar process is the lining of the tooth socket or alveolus (plural, alveoli). Although the alveolar process is composed of compact bone, it may be called the cribriform plate because it contains numerous holes where Volkmann canals pass from the alveolar bone into the PDL. The alveolar bone proper is also called bundle bone because Sharpey fibers, a part of the fibers of the PDL, are inserted here. Similar to those of the cemental surface, Sharpey fibers in alveolar bone proper are each inserted at 90 degrees, or at a right angle, but are fewer in number, although thicker in diameter than those present in cementum. As in cellular cementum, Sharpey fibers in bone are generally mineralized only partially at their periphery.
The alveolar crest is the most cervical rim of the alveolar bone proper. In a healthy situation, the alveolar crest is slightly apical to the cementoenamel junction (CEJ) by approximately 1.5 to 2 mm. The alveolar crests of neighboring teeth are also uniform in height along the jaw in healthy situation.
The supporting alveolar bone consists of both cortical bone and trabecular bone. The cortical bone, or cortical plates, consists of plates of compact bone on the facial and lingual surfaces of the alveolar bone. These cortical plates are usually about 1.5 to 3 mm thick over posterior teeth, but the thickness is highly variable around anterior teeth. The trabecular bone consists of cancellous bone that is located between the alveolar bone proper and the plates of cortical bone. The alveolar bone between two neighboring teeth is the interdental septum (or interdental bone).
The mineral content of alveolar bone is mostly calcium hydroxyapatite, which is similar to that found in higher percentages in both enamel and dentin, but is most similar to the levels in cementum (50%). Like all bone, mature alveolar bone is by weight 60% mineralized or inorganic material, 25% organic material, and 15% water. The minerals of potassium, manganese, magnesium, silica, iron, zinc, selenium, boron, phosphorus, sulfur, chromium, and others are also present but in smaller amounts. Alveolar bone is more easily remodeled than cementum, thus allowing orthodontic tooth movement. When viewing a stained histological section, the remodeled alveolar bone shows arrest lines and reversal lines, as does all bone tissue.
The developmental disturbance of anodontia (or hypodontia, if only one tooth), in which tooth germs are congenitally absent, may affect the development of the alveolar processes. This occurrence can prevent the alveolar processes of either the maxillae or the mandible from developing. Proper development is impossible because the alveolar unit of each dental arch must form in response to the tooth germs in the area.
After extraction of a tooth, the clot in the alveolus fills in with immature bone, which later is remodeled into mature secondary bone. However, with the partial or total loss of teeth, the alveolar process undergoes resorption. The underlying basal bone of the body of the maxilla or mandible remains less affected, however, because it does not need the presence of teeth to remain viable. The loss of alveolar bone, coupled with attrition of the teeth, causes a loss of height of the lower third of the vertical dimension of the face when the teeth are in maximum intercuspation. The extent of this loss is determined based on clinical judgment using the Golden Proportions.
The density of the alveolar bone in a given area also determines the route that dental infection takes with abscess formation, as well as the efficacy of local infiltration during the use of local anesthesia. In addition, the differences in alveolar process density determine the easiest and most convenient areas of bony fracture to be used, if needed during tooth extraction of impacted teeth.