M1903 Springfield

  (Redirected from Springfield M1903)

The M1903 Springfield, formally the United States Rifle, Caliber .30-06, Model 1903, is an American five-round magazine fed, bolt-action service repeating rifle, used primarily during the first half of the 20th century.

Springfield M1903
M1903 Springfield - USA - 30-06 - Armémuseum.jpg
TypeBolt-action rifle
Place of originUnited States
Service history
In service1903–1936 (as the standard U.S. service rifle)
1936–1975 (as U.S. Army sniper rifle)[1]
1937–present United States Coast Guard (as line throwing gun)
Production history
DesignerSpringfield Armory
Designed1903 (1903)
Produced1903 (1903)–1949 (1949)
No. built3,004,079[2]
VariantsSee Variants
Mass8.7 lb (3.9 kg)
Length43.2 in (1,100 mm)
Barrel length24 in (610 mm)

Cartridge.30-03; .30-06 Springfield
ActionBolt action
Rate of fire10–15 rounds/min
Muzzle velocity2,800 ft/s (850 m/s)
Effective firing range1,100 yards (1,000 m)[citation needed] with telescopic sights
Maximum firing range5,500 yards (5,000 m) with .30 M1 Ball cartridge
Feed system5-round stripper clip, 25-round (Air Service Variant) Internal Box Magazine
SightsFlip-up rear sight graduated to 2,700 yards (2,500 m), blade post-type front sight.
M1903A3: Aperture rear sight, blade type front sight.
Blade typeBayonet
M1903 Springfield with loading clips

It was officially adopted as a United States military bolt-action rifle on June 19, 1903, and saw service in World War I. It was officially replaced as the standard infantry rifle by the faster-firing semi-automatic eight-round M1 Garand starting in 1936. However, the M1903 Springfield remained in service as a standard issue infantry rifle during World War II, since the U.S. entered the war without sufficient M1 rifles to arm all troops. It also remained in service as a sniper rifle during World War II, the Korean War, and even in the early stages of the Vietnam War. It remains popular as a civilian firearm, historical collector's piece, a competitive shooting rifle, and as a military drill rifle.



During the 1898 war with Spain, the M1893 Mauser used by the Spanish Army gained a deadly reputation, particularly from the Battle of San Juan Hill where 750 Spanish regulars significantly delayed the advance of 15,000 U.S. troops armed with outclassed Springfield Model 1892–99 Krag–Jørgensen bolt-action rifles and older single-shot Springfield rifles. The Spanish soldiers inflicted 1,400 U.S. casualties in a matter of minutes. Likewise, earlier in the day, a Spanish force of 540 regulars armed with the same Mauser rifle under Spanish General Vara Del Rey held off General Henry Ware Lawton's Second Division of 6,653 American soldiers and an Independent Brigade of 1,800 men for ten hours in the nearby town of El Caney, keeping that division from assisting in the attack on the San Juan Heights. A U.S. Army board of investigation was commissioned as a direct result of both battles. They recommended replacement of the Krag.

The 1903 adoption of the M1903 was preceded by nearly 30 years of struggle and politics, using lessons learned from the recently adopted Krag–Jørgensen and contemporary German Mauser G98 bolt-action rifles. The M1903 not only replaced the various versions of the U.S. Army's Krag, but also the Lee Model 1895 and M1885 Remington–Lee used by the United States Navy and the United States Marine Corps, as well as all remaining single-shot trap-door Springfield Model 1873s. While the Krag had been issued in both a long rifle and carbine, the Springfield was issued only as a short 24-inch barrel rifle in keeping with current trends in Switzerland and Great Britain to eliminate the need for both long rifles and carbines.[3]

The two main problems usually cited with the Krag were its slow-to-load magazine and its inability to handle higher chamber pressures for high-velocity rounds. The United States Army attempted to introduce a higher-velocity cartridge in 1899 for the existing Krags, but its single locking lug on the bolt could not withstand the extra chamber pressure. Though a stripper-clip or charger loading modification to the Krag was designed, it was clear to Army authorities that a new rifle was required. After the U.S. military's experience with the Mauser rifle in the 1898 Spanish–American War, authorities decided to adopt a stronger Mauser-derived design equipped with a charger- or stripper clip-loaded box magazine.

Advances in small arms technologyEdit

In 1882, the bolt action .45 Remington Lee rifle design of 1879, with its newly invented detachable box magazine, was purchased in limited numbers by the U.S. Navy. Several hundred 1882 Lee Navy Models (M1882 Remington-Lee) were also subjected to trials by the U.S. Army during the 1880s, though the rifle was not formally adopted. The Navy adopted the Model 1885, and later different style Lee Model 1895 (a 6mm straight pull bolt), which saw service in the Boxer Rebellion. In Army service, both the 1885 and 1895 6mm Lee were used in the Spanish–American War, along with the .30 Krag and the .45-70 Model 1873 Springfield. The Lee rifle's detachable box magazine was invented by James Paris Lee, and would be very influential on later rifle designs. Other advancements had made it clear that the Army needed a replacement. In 1892, the U.S. military held a series of rifle trials, resulting in the adoption of the .30 Krag–Jørgensen rifle. The Krag officially entered U.S. service in 1894, only to be replaced nine years later by the Springfield M1903.


Thousands of Spanish Mauser Model 93 rifles, surrendered by Spanish troops in Cuba, were returned to the U.S. and extensively studied at Springfield Armory, where it was decided that the Mauser was the superior design.

U.S. Rifle Model 1900 .30 prototypeEdit

A prototype rifle was produced in 1900; it was very similar to Rifle No. 5, the final Mauser M92 prototype in the U.S. Army rifle trials of 1892. This design was rejected, and a new design combining features of the 1898 Krag rifle and the 1893 Spanish Mauser was developed.

U.S. Rifle Model 1901 .30 prototypeEdit

Springfield began work on creating a rifle that could handle higher loads around the turn of the 20th century. The Springfield Model 1901 prototype combined the cock-on-opening bolt, 30" barrel, magazine cutoff, stock and sights of the Krag–Jørgensen with the dual locking lugs, external claw extractor, and staggered-column magazine of the 1893 Mauser. Taking a cue from the 1898 Mauser Gewehr 98, a large safety lug was added to the side of the bolt behind the extractor, which would engage the receiver bridge and prevent the bolt moving rearwards. The bolt handle was also bent downwards, to make operation of the bolt faster. The Springfield Model 1901 almost entered production. Springfield was sure enough that the Springfield Model 1901 prototype would be accepted that they began making some parts, but it was not accepted and further changes were asked for.


Following then-current trends in service rifles, the barrel was shortened to 24" after it was discovered that a longer barrel offered no appreciable ballistic advantage, and the shorter barrel was lighter and easier to handle. This "short rifle" also eliminated the need of a shorter carbine for mounted troops or cavalry.[4] A spike-type bayonet with storage in the fore end of the stock was added to the design. This new design was accepted, type classified and officially adopted as the United States Rifle, Caliber .30, Model 1903 and entered production in 1903. The M1903 became commonly known among its users as the "ought-three" in reference to the year '03 of first production.

The War Department had exhaustively studied and dissected several examples of the Spanish Mauser Model 1893 rifle captured during the Spanish–American War, and applied some features of the U.S. Krag rifle to a bolt and magazine system derived from the Mauser Model 93, to produce the new U.S. Springfield Rifle, the Model 1903. Despite Springfield Armory's use of a two-piece firing pin and other slight design alterations, the 1903 was, in fact, a Mauser design, and after that company brought suit, the U.S. government was judged to pay $250,000 in royalties to Mauser Werke.[5]

By January 1905 over 80,000 of these rifles had been produced at the federally owned Springfield Armory. However, President Theodore Roosevelt objected to the design of the sliding rod-type bayonet used as being too flimsy for combat. In a letter to the Secretary of War, he said:

I must say that I think that ramrod bayonet is about as poor an invention as I ever saw. As you observed, it broke short off as soon as hit with even moderate violence. It would have no moral effect and mighty little physical effect.[6]

All the rifles to that point consequently had to be re-tooled for a blade-type bayonet, called the M1905. The sights were also an area of concern, so the new improved Model 1904 sight was also added.[4][7]

The retooling was almost complete when it was decided another change would be made. It was to incorporate improvements discovered during experimentation in the interim, most notably the use of pointed ammunition, first adopted by the French in the 1890s and later other countries. The round itself was based on the .30-03, but rather than a 220-grain (14 g) round-tip bullet fired at 2,300 ft/s (700 m/s), it had a 150-grain (9.7 g) pointed bullet fired at 2,800 ft/s (850 m/s); the case neck was a fraction of an inch shorter as well. The new American cartridge was designated "Cartridge, Ball, Caliber .30, Model of 1906". The M1906 cartridge is better known as the .30-06 Springfield round used in many rifles and machine guns, and is still a popular civilian cartridge to the present day. The rifle's sights were again re-tooled to compensate for the speed and trajectory of the new cartridge.

By the time of the 1916 Pancho Villa Expedition the 1903 Springfield Rifle was the standard issue service rifle of US forces. Some rifles were fitted with both the Warner & Swasey Model 1913 and 1908 "Musket Sights" during the campaign. "Musket Sights" being the vernacular at the time for telescopic sights. Annecdotal evidence at the time indicates that some of the rifles were fitted with Maxim silencers, which would make them the first U.S. Military Suppressed Rifles. The Warner & Swasey Model 1913 Musket Sight would continue to see service after the Pancho Villa Expedition and during World War I but would be deemed inadequate and was removed from the US Army's inventory by the 1920s. [8]

World War I and interwar useEdit

US Marines with M1903 rifles and bayonets in France (1918)
An Elder-type periscope stock fitted to an M1903 (1918). Designed for trench warfare, this enabled the shooter to fire over the parapet of a trench while remaining under cover and protected; the rifle is also fitted with a 25-round magazine.[9]
The Pederson device outfitted to the M1903 allows it to fire .30 calibre pistol-grade cartridges in semi-automatic fire mode.

By the time of U.S. entry into World War I, 843,239 of these rifles had been produced at Springfield Armory and Rock Island Arsenal. Pre-war production utilized questionable metallurgy. Some receivers constructed of single-heat-treated case-hardened steel were improperly subjected to excessive temperatures during the forging process. The carbon could be "burnt" out of the steel producing a brittle receiver.[10] Despite documented evidence indicating some early rifles were improperly forged, actual cases of failure were very rare. Although several cases of serious injury from receiver failure were documented, the U.S. Army never reported any fatalities. Many failures were attributed to use of incorrect cartridges, such as the 7.92×57mm Mauser.[11] Evidence also seems to suggest that improperly forged brass cartridge cases could have exacerbated receiver failure.[12]

Pyrometers were installed in December 1917 to accurately measure temperatures during the forging process. The change was made at approximately serial number 800,000 for rifles made at Springfield Armory and at serial number 285,507 at Rock Island Arsenal. Lower serial numbers are known as "low-number" M1903 rifles. Higher serial numbers are said to be "double-heat-treated."[11]

Toward the end of the war, Springfield turned out the Model 1903 Mark I. The Mark I has a cut on the left hand side of the receiver meant to act as an ejection port for the Pedersen Device, a modified sear and cutoff to operate the Pedersen Device; a specialized insert that replaced the bolt and allowed the user to fire .30 caliber pistol cartridges semi-automatically from a 40-round detachable magazine. The stock was also slightly cut down on the left side to clear the ejection port. In all other respects, the Mark I is identical to the 1903. Temperature control during forging was improved prior to Mark I production. The receiver alloy was toughened by addition of nickel after Mark I production.

In 1926, after experiencing the effect of long-range German 7.92×57mm Mauser and machine gun fire during the war, the U.S. Army adopted the heavy 174-grain boat-tail bullet for its .30-06 cartridge, standardized as 'Cartridge, Ball, caliber 30, M1'.[13] M1 ammunition, intended primarily for long-range machine gun use, soon became known by Army rifle competition teams and expert riflemen for its considerably greater accuracy over that of the M1906-round; the new M1 ammunition was issued to infantrymen with the Springfield rifle as well as to machine gun teams.[14] However, during the late 1930s, it became apparent that, with the development of mortars, high-angle artillery, and the .50 caliber M2 Browning machine gun, the need for extreme long-range, rifle-caliber machine-gun fire was decreasing. In 1938, the U.S. army reverted to a .30-06 cartridge with a 152-grain flat-base bullet, now termed M2 Ball, for all rifles and machine guns.[13]

In the 1920s and the 1930s, M1903s were delivered to US allies in Central America, such as Cuba, Costa Rica or Nicaragua. Costa Rica troops were equipped with Springfields during the Coto War and some rifles were captured by the opposing Panamanians.[15] The Cuban Springfields will be used by Batista forces after WW2 and later by the Revolutionary Armed Forces, for instance during the Bay of Pigs Invasion.[16]

The Federal Bureau of Investigation acquired some M1903 rifles configured like National Rifle Association Sporter Models in response to the 1933 Kansas City Massacre.[17]

In service, the Springfield was generally prized for its reliability and accuracy, though some problems remained. The precision rear aperture sight was located too far from the eye for efficient use, and the narrow, unprotected front sight was both difficult to see in poor light and easily damaged. The U.S. Marine Corps issued the Springfield with a sight hood to protect the front sight, along with a thicker front blade. The two-piece firing pin/striker also proved to be no improvement over the original one-piece Mauser design, and was a cause of numerous Ordnance repairs, along with occasional reports of jammed magazine followers.[18]

Camouflaged M1903 Springfield sniper's rifle with Warner & Swasey telescopic sight, in France, May 1918.

World War IIEdit

World War II saw new production of the Springfield at private manufacturers such as the Remington Arms and Smith-Corona Typewriter companies. Remington began production of the M1903 in September 1941, at serial number 3,000,000, using old tooling from the Rock Island Arsenal which had been in storage since 1919. The very early rifles are almost indistinguishable from 1919-made Rock Island rifles. As the already worn tooling began to wear beyond use Remington began seeking Army approval for a continuously increasing number of changes and simplifications to both speed up manufacture and improve performance. The milled parts on the Remington M1903 were gradually replaced with stamped parts until, at about serial number 3,330,000, the Army and Remington recognized that a new model name was appropriate. Other features of the M1903, such as high-grade walnut stocks with finger grooves, were replaced with less expensive but serviceable substitutes. Most milled parts made by Remington were marked with an "R".[19]

M1903 production was discontinued in favor of the M1903A3. The most noticeable visual difference in the M1903A3 was the replacement of the barrel-mounted rear sight with a smaller, simpler aperture rear sight mounted on the rear of the receiver; it was primarily adopted in order to speed familiarization by soldiers already trained on the M1 Garand, which had a similar sighting system. However, the leaf spring providing tension to the elevation adjustment on the new aperture sight tended to weaken with continued use over time, causing the rifle to lose its preset range elevation setting.[18] Other modifications included a new stamped cartridge follower; ironically, the rounded edges of the new design largely alleviated the 'fourth-round jam' complaints of the earlier machined part.[18] All stock furniture was also redesigned in stamped metal.

In late 1942, Smith-Corona Typewriter Company also began production of the M1903A3 at its plant in Syracuse, NY.[20] Smith/Corona parts are mostly identified by the absence of markings, except for occasions when time permitting during manufacture, on early to mid production rifles, and also only on certain parts.

To speed up production output, two-groove rifled barrels were adopted, and steel alloy specifications were relaxed under 'War Emergency Steel' criteria for both rifle actions and barrels.[21] M1903A3 rifles with two-groove 'war emergency' barrels were shipped with a printed notation stating that the reduction in rifling grooves did not affect accuracy.[22] As the war progressed, various machining and finishing operations were eliminated on the M1903A3 in order to increase production levels.[22]

Original production rifles at Remington and Smith-Corona had a dark gray/black finish similar to the bluing of late World War I. Beginning in late 1943 a lighter gray/green parkerizing finish was used. This later finish was also used on arsenal repaired weapons.

It is somewhat unusual to find a World War I or early World War II M1903 with its original dated barrel. Much, if not all, World War II .30-06 ammunition used a corrosive primer which left corrosive salts in the barrel. If not removed by frequent and proper barrel cleaning these residues could cause pitting and excessive wear. In the jungle fighting on various Pacific islands cleaning was sometimes lax and the excessive moisture compounded the corrosive action of the residue.[23]

The M1903 and the M1903A3 rifle were used in combat alongside the M1 Garand by the U.S. military during World War II and saw extensive use and action in the hands of U.S. troops in Europe, North Africa, and the Pacific. The U.S. Marines were initially armed with M1903 rifles in early battles in the Pacific, such as the Battle of Guadalcanal, but the jungle battle environment generally favored self-loading rifles;[24] later Army units arriving to the island were armed with the M1 Garand.[25] The U.S. Army Rangers were also a major user of the M1903 and the M1903A3 during World War II with the Springfield being preferred over the M1 Garand for certain commando missions.

According to Bruce Canfield's encyclopedic U.S. Infantry Weapons of WW II, final variants of the M1903 (the A3 and A4) were delivered in February 1944.[19] By then, most American combat troops had been re-equipped with the M1 Garand. However, some front-line infantry units in both the U.S. Army and Marine Corps retained M1903s as infantry rifles beyond that date and continued to use them alongside the M1 Garand until the end of the Second World War in 1945. The Springfield remained in service for snipers (using the M1903A4), grenadiers (using a spigot type rifle 22 mm with the M1 grenade launcher] grenade launcher until the M7 grenade launcher was available for the M1 rifle in late 1943), and Marine Scout Sniper units.

Sniper rifleEdit

The M1903A4 was the U.S. Army's sniper rifle of choice during the Second World War. The M1903A4 was a variation of the M1903A3. The only difference between receivers was that the model and serial number on the receiver were split on 1903A4 to make room for the Redfield scope mount. The Redfield scope mount removed the rear peep sight that was standard on the M1903A3. The scope used on the M1903A4 was a Weaver Model 330 or 330C, which was a 2.75x telescopic sight. The receivers were tested by Remington Arms and those that were deemed best, meaning those closest to design specifications were selected to become M1903A4's. The barrels were also selected specifically to be added to the M1903A4 rifle only if they were within almost exact specifications for the design. The front sight on the barrel was never installed on the A4 barrels, however, the notch for it was still in place. .[18] Barrel specifications were, in general, unchanged between the M1903A3 and M1903A4, however, the War Department did start installing barrels with 2 groove rifling instead of 4 groove, despite the lack of clear changes from the 4 groove rifling that was the standard up until 1942.[26]

By some accounts, the M1903A4 was inadequate as a sniper rifle. The M1903A4 was a relatively accurate rifle with an effective range of about 600 yards (550m). These limitations on long-range targeting were due to the limited field of view present in both the Weaver scopes. From its adoption in 1943 until the end of the war it was used extensively in every theater of operation by both the US Army and the USMC.[27] The Weaver scopes (later standardized as the M73 and M73B1) were not only low-powered in magnification, they were not waterproofed, and frequently fogged over or became waterlogged during humidity changes. In addition, the M81/82 optional scopes also had significant flaws. They most notably had less power (2.2x vs. 2.75x) and, like the other scopes on the M1903A4, had serious issues with the field of view.[18][27][28] The USMC would eventually switch to a large 8x scope that spanned the length of the rifle designed by John Unertl.

Foreign usersEdit

The U.S. Army Military Police (MP) and the U.S. Navy Shore Patrol also used M1903s and M1903A3s throughout the war. Various U.S. allies and friendly irregular forces were also equipped with the weapon. The Brazilian Expeditionary Force (FEB), operating in the 5th Army in Italy was equipped with Springfield M1903 rifles. In August 1943, the Free French Forces of General Charles de Gaulle were re-equipped by the United States primarily with M1903A3 Springfield and M1917 Enfield Rifles. The M1903A3 became one of the primary rifles used by French forces until the end of the war, and was afterwards used in Indochina[29] and by local militia and security forces in French Algeria.[30] Large numbers of M1903 Springfields were sent to China.[31]

During the Korean War, South Korean Marines used M1903A3[32]

South Korean marine armed with M1903 rifle, September 20, 1950.

Springfield M1903 rifles captured by the Germans were designated Gewehr 249(a).[33]

Post–Korean War serviceEdit

After the Korean War, active service (as opposed to drill) use of the M1903 was rare. Still, some M1903A4s remained in sniper use as late as the Vietnam War; and technical manuals for them were printed as late as 1970.[4] The U.S. Navy also continued to carry some stocks of M1903A3s on board ships, for use as anti-mine rifles.


M1903 Springfield with 8x Unertl scope used during a vintage sniper rifle match in 2012

Due to its balance, it is still popular with various military drill teams and color guards, most notably the U.S. Army Drill Team.[citation needed] M1903 rifles (along with the M1 Garand, M1917 Enfield and M14 rifles) are also common at high school Junior Reserve Officer Training Corps (JROTC) units to teach weapons handling and military drill procedures to the cadets. JROTC units use M1903s for regular and inter-school competition drills, including elaborate exhibition spinning routines. Exhibition teams often use fiberglass stocks in place of wooden stocks, which are heavier and more prone to breakage when dropped. JROTC Color Guards still favor wooden stocks over fiberglass because of their weight characteristics and appearance. The M1903 is also the standard parade rifle of the Virginia Tech Corps of Cadets, which has over six hundred M1903s, a very small percentage of which are still fireable. The Summerall Guards of The Citadel South Carolina Corps of Cadets in Charleston, S.C. also use the Springfield 1903 model for their silent drill performances, which include annual trips to Mardi Gras, as well as many other notable performances.

Contemporary hunters and shooting enthusiasts value the rifle for its beauty, dependability, and adaptability for almost all U.S. game animals.[citation needed]

U.S. Naval Sea Cadet Corps color guard rifles bear many similarities to the Springfield.

In 1977, the Army located a rather large cache of unissued M1903A3 rifles which were demilitarized and then issued to JROTC units as a replacement for their previously issued M1 Garand and M14 rifles, which were then returned to Army custody due to concerns about potential break-ins at high school JROTC armories.

For safety reasons, the JROTC M1903s are made permanently unable to fire by plugging the barrel with a steel rod, or having it filled with lead, soldering the bolt and welding the magazine cutoff switch in the ON position. To plug the barrel, a very cold steel rod was inserted; after it warmed up it was too tight to remove.


Diagram of the .30 Springfield Rifle

The U.S. rifle, Model of 1903 was 44⅞ inches (1.098 m) long and weighed 8 lb 11 oz (3.95 kg). A bayonet could be attached; the M1905 bayonet blade was 16 in (406 mm) long and weighed 1 lb (0.45 kg). From 1906, the rifle was chambered to fire the .30-caliber M1906 cartridge (.30-06 cartridge), later the M1 (1926) and M2 Ball (1938) rounds. There were four standard types of cartridge:

  • Ball: consisted of a brass case or shell, primer, a charge of smokeless powder, and the bullet. The bullet had a sharp point called a spitzer bullet, and was composed of a lead core and a jacket of cupro-nickel (later gilding metal), and in the M1906 design, weighed 150 grains (9.7 g). The bullet of the M1906 cartridge, when fired from the rifle, had an initial velocity of 2,700 ft/s (820 m/s).
  • Blank: contained a paper cup instead of a bullet. It is dangerous up to 33 yd (30 m).
  • Guard: had a smaller charge of powder than the ball cartridge, and five cannelures encircle the body of the shell at about the middle to distinguish it from ball cartridges. It was intended for use on guard or in riot duty, and it gave good results up to 200 yd (180 m). The range of 100 yd (91 m) required a sight elevation of 450 yd (410 m), and the range of 200 yd (180 m) required an elevation of 645 yd (590 m).
  • Dummy: this was tin-plated and the shell was provided with six longitudinal corrugations and three circular holes. The primer contains no percussion composition. It was intended for drill purposes to accustom the soldier to the operation of loading the rifle.

The rifle was sighted for 2,500 yd (2,300 m) and had a point-blank range of 500 yd (460 m). The maximum range of the ball cartridge, when elevated at an angle of 45°, was 4,890 yd (4.47 km; 2.78 mi).

The rifle was a magazine-fed clip-loader and could fire at a rate of 20 shots per minute. Each stripper clip contained five cartridges, and standard issue consisted of 12 clips carried in a cloth bandoleer. When full the bandoleer weighed about 3 lb 14 oz (1.8 kg). Bandoleers were packed 20 in a box, for a total of 1,200 rounds. The full box weighed 100 lb (45 kg).

The bore of the rifle is 0.30 inches (7.62 mm) in diameter. It was then rifled 0.004 in (0.1 mm) deep, making the diameter from the bottom of one groove to the bottom of the opposite groove 0.30787 in (7.82 mm) of the barrel.

The 1903 rifle included a rear sight leaf that could be used to adjust for elevation. When the leaf was flat, the battle sight appeared on top. This sight was set for 547 yd (500 m), and was not adjustable. When the leaf was raised it could be adjusted to a maximum extreme range of 2,850 yd (2,610 m). The rear sight could also be adjusted for windage.

The 1903A3 rear sight was an aperture sight adjustable both for elevation and windage.

A feature inherent to the M1903 and not found on the Mauser 98 is the cocking piece, a conspicuous knob at the rear of the bolt, allowing the rifle's striker to be released without dry firing, or to cock the rifle if necessary, for example to attempt a second strike on a round that failed to fire.


There were four main variants given official nomenclature, though there are a number of important sub-variants:

M1903 with 'scant' stock
M1903A4 with Type C stock and M84 sight
  • M1903 (1903): developed for the .30-03 (also known as the .30-45) cartridge. Used original Type S stock.
    • M1903 Bullpup (1903): experimental bullpup conversion for the USMC.[34][failed verification]
    • M1903 (1905): changed from a rod type bayonet to the knife type Model 1905 bayonet and to the improved Model 1905 sight.
    • M1903 (1906): modified again to specifically fire the new M1906 .30-06 cartridge ("Ball Cartridge, caliber 30, Model of 1906").
    • M1903 NRA (1915–1917): sold to National Rifle Association members and stamped NRA on the forward tang of the trigger guard.[35]
    • M1903 Air Service (1918): issued to aircrew with permanent 25-round magazine and modified Type S stock forend designed as backup for if a plane's machine gun jammed in combat.[36]
    • M1903 Mark I (1918–1920): modified for specific use with the Pedersen device.
    • M1903 NM (1921–1940): selected rifles produced at Springfield Armory for National Match shooting competition. Production barrels were measured with star-gauges, and those meeting specified tolerances were stamped with an asterisk shaped star on the muzzle crown. These barrels were fitted to selected receivers with hand-fitted and polished parts. The bolt was left unblued while the receiver and barrel were finished with a black Parkerizing process. Some bolts have the safety direction reversed to prevent it from striking the nose of a right-handed shooter, and those made from 1924 to 1929 have the knurled cocking piece removed to decrease lock time. Early rifles used the type S stock until the type C stock became standard in 1929. Rifles made for sale to NRA members (priced at $40.44) were drilled and tapped for a Lyman 48 receiver sight and had either a type B (or NB) stock with no grasping grooves and a noticeable drop at the heel for a long pistol grip, or a special National Match stock with a high comb and pistol grip. Total production was 28,907. Most were issued to service teams and 25,377 were reconditioned at Springfield armory after one year of match use. Reconditioned rifles have a large gas-escape port drilled into the left side of the receiver.[37]
    • M1903 Bushmaster carbine (1940s): the barrel and stock were cut down to 18 inches (460 mm) for easier use in Panama; 4,725 such rifles were made. It was a training rifle and saw no action. After World War II most were dumped into the ocean and surviving pieces are rare.
    • M1903 with 'scant' stock (1942): in late 1941, before the 1903A3 was standardized, Army Ordnance wanted to standardize on a pistol-grip stock for all M1903 rifles. There were thousands of stock blanks that had been sized for the old straight stock. They weren't deep enough for the full pistol grip of the Type C stock, so they were modified to allow a "scant" grip that was the largest grip they could form. These "scant" stocks would only fit on a 1903, and would not fit an 03A3. Springfield only rebuilt existing M1903 rifles using this stock in 1942 and marked the cut-off seat with a small "s".
Springfield 1903A1 rifle
  • M1903A1 (1929–1939): changed from a straight stock to a pistol grip type stock (Type C stock). The pistol grip stock was conducive to improved marksmanship and was fitted to National Match rifles until World War II. Pistol grip stocks became standard for later M1903 production and were subsequently fitted to older rifles. The Army considered any rifle with a pistol grip stock an M1903A1, but M1903 receiver markings were unchanged.[38]
  • M1903A2 (1930s–1940s): basically a stripped A1 or A3 used as a subcaliber rifle with artillery pieces.
  • M1903A3 (1942–1944): sights were changed to an aperture (peep) system mounted on the receiver, and the rifle was modified for easier production with stamped metal parts and somewhat different grip and stock (late model Type S stock; no finger grooves).
    • M1903 (Modified) (1941–1942): Transition production of M1903 rifles by Remington Arms until the M1903A3 design was implemented involved modification of various parts creating a hybrid between the M1903 and M1903A3.[19]
  • M1903A4 (1942): an M1903A3 modified to be a sniper rifle using an M73 or M73B1 2.5× Weaver telescopic sight and different stock, and omitting the iron sights. USMC versions instead used the 8x Unertl scope.

There are two main other types, various training types, and competition versions such as the National Match types. Aside from these there are some other civilian versions, experimental versions, and other miscellaneous types. Due to the duration of its service, there is also a range of smaller differences among ones from different periods and manufacturers.

In military use it was outnumbered by the M1917 Enfield for much of the war. Also, during World War II many remained in use early on, especially in the Pacific (generally replaced as M1s became available), in addition to service (along with other weapons) as a sniper rifle and to launch rifle grenades.

  • Bannerman Springfields: At the outbreak of World War I in 1914, the Scottish-born military surplus magnate, Francis Bannerman VI (1851–1918), assembled 1,000 M1903 rifles from surplus parts which were rebored to accept British .303 ammunition. These he presented to the British Army together with the associated bayonets, pouches and webbing, as a patriotic gesture. Unfortunately, the conversion was not a success and it was found that the rimmed .303 cartridge would not feed properly from the magazine.[39] The rifles were stamped "DP", i.e. fit for "drill purposes" only, and presented to the City of London Volunteer Training Corps who were otherwise without any weapons.[40]

In popular cultureEdit

Ernest Hemingway used this rifle, with iron sights, to shoot big game, including lions, on his first African safari in 1933. That safari is the subject of Green Hills of Africa, published in 1935.

This rifle was used by Private Daniel Jackson in the film Saving Private Ryan.

The Springfield 01 is the primary long-range weapon in the Destroyermen series by Taylor Anderson


See alsoEdit


  1. ^ "The 1903 Springfield Rifle – Warfare History Network". January 18, 2019.
  2. ^ "SPRINGFIELD ARMORY US MODEL 1903 RIFLE SERIAL NUMBER RANGES". Bowers Firearms. Retrieved 8 October 2017.
  3. ^ Chisholm, Hugh, ed. (1911). Encyclopædia Britannica: A Dictionary of Arts, Sciences, Literature and General Information, Volumes 23–24 (11 ed.). University Press. p. 328.
  4. ^ a b c Canfield, Bruce N. (2003). "100 Years Of The '03 Springfield". American Rifleman. 151 (March): 42–45&78.
  5. ^ Sheehan, John (1 October 2006). "Battlefield tack driver: the model 1903 Springfield in WWI". Guns Magazine. Retrieved 22 April 2015.
  6. ^ Kontis, George (24 August 2011). "Are We Forever Stuck with the Bayonet?". Small Arms Defense Journal. Retrieved 22 April 2015.
  7. ^ Canfield, Bruce N. (2006). "From Poor Invention To America's Best". American Rifleman. 154 (September): 59–61, 91–92&94.
  8. ^ Canfield, Bruce (October 2016). "1916: Guns On The Border". American Rifleman. National Rifle Association.
  9. ^ Ordnance Dept, United States. Army (15 November 1918). "Bayonet" (Digital). Handbook of Ordnance Data. U.S. Government Printing Office: 332. OCLC 6316176.
  10. ^ Canfield, February 2008, p. 13
  11. ^ a b Canfield, Bruce N. (2004). "U.S. M1903A1 Rifles". American Rifleman. 152 (January): 20.
  12. ^ Lyon, Joseph: Some Observations On The Failure Of U.S. Model 1903 Rifle Receivers <http://m1903.com/03rcvrfail/>
  13. ^ a b Barnes, Frank C., Cartridges of the World, 6th ed., DBI Books Inc. (1989), p. 59
  14. ^ Dunlap, Roy (1948). "Rifles". Ordnance Went up Front: Some Observations and Experiences of a Sergeant of Ordnance, Who Served Throughout World War II with the United States Army in Egypt, the Philippines and Japan, Including Way Stations. OCLC 777744849.
  15. ^ a b c Jowett, Philip (28 Jun 2018). Latin American Wars 1900–1941: "Banana Wars," Border Wars & Revolutions. Men-at-Arms 519. Osprey Publishing. pp. 15, 17, 45. ISBN 9781472826282.CS1 maint: ref=harv (link)
  16. ^ de Quesada, Alejandro (10 Jan 2009). The Bay of Pigs: Cuba 1961. Elite 166. p. 60. ISBN 9781846033230.
  17. ^ Vanderpool, Bill "Bring Enough Gun" American Rifleman October 2013 pp. 80–85&115–116
  18. ^ a b c d e Dunlap, Roy, Ordnance Went Up Front, Samworth Press (1948), p. 302
  19. ^ a b c Canfield, Bruce N. (2015). "Wartime Remington M1903s?". American Rifleman. 163 (March): 44.
  20. ^ Brophy, William, The Springfield 1903 Rifles, Stackpole Books (1985), p. 187
  21. ^ Dunlap, Roy, Ordnance Went Up Front, Samworth Press (1948), p. 362
  22. ^ a b Dunlap, Roy, Ordnance Went Up Front, Samworth Press (1948), p. 301
  23. ^ Bishop, Chris (1998), The Encyclopedia of Weapons of World War II, New York: Orbis Publishing Ltd, ISBN 978-0-7607-1022-7
  24. ^ George, John (Lt Col), Shots Fired In Anger, NRA Press (1981), p. 391: "Nearly every one [Marine] I talked to [on Guadalcanal] who used the Springfield in combat-without a scope-would have much rather been using a Garand."
  25. ^ George, John (Lt Col), Shots Fired In Anger, NRA Press (1981), p. 391
  26. ^ George, John (Lt. Col.), Shots Fired In Anger, NRA Press (1981), p. 392
  27. ^ a b George, John (Lt. Col.), Shots Fired In Anger, NRA Press (1981), p. 392–393
  28. ^ George, John (Lt. Col.), Shots Fired In Anger, NRA Press (1981), p. 296–299
  29. ^ Windrow, Martin (20 Sep 2018). French Foreign Légionnaire vs Viet Minh Insurgent: North Vietnam 1948–52. Combat 36. Osprey Publishing. p. 22. ISBN 9781472828910.
  30. ^ "L'armement français en A.F.N." Gazette des Armes (in French). No. 220. March 1992. pp. 12–16.
  31. ^ a b Jowett, Philip (10 Jul 2005). The Chinese Army 1937–49: World War II and Civil War. Men-at-Arms 424. Osprey Publishing. p. 19. ISBN 9781841769042.
  32. ^ 부, 창옥 (2012). 한국 전쟁 수첩: 어느 학도병 의 참전 일기. 경기 고양시: 한그루 미디어. p. 6. ISBN 9791195158027.
  33. ^ Ball, Robert W. D. (2011). Mauser Military Rifles of the World. Iola: Gun Digest Books. p. 420. ISBN 9781440228926.
  34. ^ "Photo". s-media-cache-ak0.pinimg.com. Retrieved 2020-06-02.
  35. ^ Canfield, Bruce N. American Rifleman (September 2008) pp. 72–75
  36. ^ Forgotten Weapons (2017-11-28), Fight! Othais vs Ian on the Air Service 1903 Springfield!, retrieved 2017-11-29
  37. ^ Norell, James O.E. (2003). "U.S. M1903A1 Rifles". American Rifleman. 151 (July): 38–41.
  38. ^ Canfield, Bruce N. (2007). "U.S. M1903A1 Rifles". American Rifleman (January): 38.
  39. ^ Ian D. Skennerton, The Lee Enfield: A Century of Lee-Metford & Lee-Enfield Rifles & Carbines, Arms & Militaria Press 2007, ISBN 978-0-949749-82-6 (p. 162)
  40. ^ Foster, Alfred Edye Manning (June 2, 1920). "The National guard in the great war, 1914–1918". London : Cope & Fenwick – via Internet Archive.
  41. ^ Maximiano, Cesar; Bonalume, Ricardo N (2011). Brazilian Expeditionary Force in World War II. Men at Arms 465. Osprey Publishing. pp. 10, 16–17, 44. ISBN 9781849084833.
  42. ^ a b c d e f g h Thompson 2013, p. 63.
  43. ^ a b Rottman, Gordon L. (10 Feb 2009). North Vietnamese Army Soldier 1958–75. Warrior 135. Osprey Publishing. p. 21. ISBN 9781846033711.
  44. ^ a b Windrow, Martin (15 Nov 1998). The French Indochina War 1946–54. Men-at-Arms 322. Osprey Publishing. p. 41. ISBN 9781855327894.
  45. ^ Scarlata, Paul (Mar 1, 2009). "Ethiopian military rifle cartridges: Part 2: from Mauser to Kalashnikov". Shotgun News.
  46. ^ "Uphold Democracy 1994: WWII weapons encountered". wwiiafterwwii.wordpress.com. 9 June 2015.
  47. ^ Holden, Robert H. (2004). Armies without Nations: Public Violence and State Formation in Central America, 1821–1960. Oxford and New York: Oxford University Press. p. 287. ISBN 9780198036517.
  48. ^ "Philippines pt.2: WWII weapons used 1946-2018". wwiiafterwwii.wordpress.com. November 18, 2018.
  49. ^ Rottman, Gordon L. (December 2002). Korean War Order of Battle: United States, United Nations, and Communist Ground, Naval, and Air Forces, 1950–1953. Praeger. p. 193. ISBN 978-0-275-97835-8.
  50. ^ Conboy, Kenneth (23 Nov 1989). The War in Laos 1960–75. Men-at-Arms 217. Osprey Publishing. p. 15. ISBN 9780850459388.
  51. ^ Bloomfield, Lincoln P.; Leiss, Amelia Catherine (30 June 1967). The Control of local conflict : a design study on arms control and limited war in the developing areas (PDF). 3. Massachusetts Institute of Technology. Center for International Studies. pp. 80, 89. hdl:2027/uiug.30112064404368.
  52. ^ a b Brophy, William, The Springfield 1903 Rifles, Stackpole Books (1985), p. 149
  53. ^ Reynolds, Dan. "The Mauser Rifles of Peru". carbinesforcollectors.com. Retrieved 22 January 2019.
  54. ^ "Springfield M1903 Bolt Action Rifle". Armas de las Islas Filipinas. July 22, 2011.
  55. ^ Brophy, William, The Springfield 1903 Rifles, Stackpole Books (1985), p. 150


  • Thompson, Leroy (20 February 2013). The M1903 Springfield Rifle. Weapon 23. Osprey Publishing. ISBN 9781780960111.CS1 maint: ref=harv (link)
  • Ball, Robert W. D., Springfield Armory Shoulder Weapons 1795–1968. Norfolk, VA: Antique Trader Books, 1997. ISBN 0-930625-74-9 OCLC 39273050
  • Canfield, Bruce N. (February 2008). ""Low Number" M1903 Springfields". American Rifleman.
  • Engineer Field Manual, War Department, Document No. 355, 1909.
  • Manual for Noncommissioned Officers and Privates of Infantry of The Army of the United States, War Department, Document No. 574, 1917.
  • "Bushmaster '03 Carbine," American Rifle magazine, April 2005, p. 40.
  • U.S. Infantry Weapons of World War II. Bruce N. Canfield, Andrew Mowbray Publishers, 1994.

External linksEdit