Open main menu

The Rolls-Royce RB.80 Conway was the first turbofan engine to enter service. Development started at Rolls-Royce in the 1940s, but the design was used only briefly, in the late 1950s and early 1960s, before other turbofan designs replaced it. However, the Conway engine was used in versions of the Handley Page Victor, Vickers VC10, Boeing 707-420 and Douglas DC-8-40. The name "Conway" is the English spelling of the River Conwy, in Wales, in keeping with Rolls' use of river names for gas turbine engines.

Conway
RRConway.JPG
RCo.17 Mk201
Type Turbofan
Manufacturer Rolls-Royce Limited
Major applications Boeing 707
Douglas DC-8
Handley Page Victor
Vickers VC10

Contents

DevelopmentEdit

BackgroundEdit

In early jet engines, the exhaust was much faster and hotter than it had to be for efficient thrust, contrary to the ideal Froude efficiency. Capturing some of that energy would improve the fuel economy of the engine. The turboprop engine is an obvious example, which uses a series of additional turbine stages to capture the exhaust energy and power a propeller. However, there is a trade-off in propeller efficiency compared to forward speed, so turboprop engines are only efficient at speeds of up to 500 mph (800 km/h; 430 kn). This means there is a sweet spot between the efficiencies of the turboprop at low speeds and the jet at high speeds that was not being directly tackled. This spot, between about 450 mph (720 km/h; 390 kn) and 700 mph (1,100 km/h; 610 kn), was precisely where the vast majority of commercial jet aircraft spent most of their time.

The basic concept of bypass had been studied from the earliest days of jet engine design. Alan Arnold Griffith had proposed a number of different bypass engine designs as early as the 1930s while he and Hayne Constant were trying to get their axial-flow jet engines working at the Royal Aircraft Establishment. Frank Whittle's Power Jets also studied a number of bypass configurations. However, the need to get jet engines into service during the war meant that work had to be put aside in favour of the simpler turbojet designs with shorter introduction times. Priorities changed dramatically at the end of the war and, by 1946, Rolls-Royce agreed that existing engines like the Rolls-Royce Avon were advanced enough to enable a start to work on more advanced concepts like bypass.

In a bypass design some of the air from the compressor bypasses the hot core of the engine — the combustion chambers and turbine — and by being channelled around the outside of this section and then out of the back of the engine, where it surrounds the high velocity jet exhaust, it is used to provide thrust directly. Due to not being accelerated by combustion in the hot section, the colder air emerges at the back of the engine at a lower velocity than the jet exhaust, one which is nearer to the aircraft's airspeed in relation to the surrounding atmosphere, thus improving the Froude efficiency. In addition to reducing fuel consumption compared with that of a simple turbojet, a beneficial side effect is that the core of hot gas from the jet exhaust is surrounded by a tube of colder, slower moving air, reducing noise. Rolls-Royce termed the design a Bypass Turbojet.

Griffith, who by then had become Chief Engineer at Rolls-Royce, suggested building a purely experimental bypass design using parts of the Avon and another experimental jet engine, the AJ.25 Tweed. In April 1947, a 5,000-pound-force (22,000 N) design was proposed, but over the next few months it was modified to evolve into a larger 9,250-pound-force (41,100 N) design in response to a need for a new engine to power the Mk.2 low-level version of the Vickers Valiant bomber. The go-ahead to start construction of this larger design was given in October, under the name RB.80.

Early modelsEdit

During development it was decided to further improve the basic design by adding another feature then becoming common, a "two spool" compressor arrangement. Earlier engines generally consisted of a series of compressor stages connected via a shaft to one or more turbine stages, with the burners between them arranged around the shaft. Although this arrangement is mechanically simple, it has the disadvantage of lowering the efficiency of the compressor. Compressor stages run at their maximum efficiency when spinning at a specific speed for any given input air pressure - in a perfect compressor each stage would run at a separate speed. The multi-spool design, first used on the Bristol Olympus turbojet,[1] is a compromise, the compressor being separated into "spools" designed to operate closer to most efficient speed, driven by separate turbines via concentric shafts. Two- and three-spool designs are common; beyond that the mechanical complexity is too great.

The new version had a four-stage low-pressure compressor driven by a two-stage turbine and an eight stage high-pressure compressor driven by another two-stage turbine. Now known by the Ministry of Supply designation as the RCo.2, design work was completed in January 1950 and the first example ran for the first time in July 1952 at 10,000 pounds-force (44,000 N) thrust. By this time, the low-level Valiant Pathfinder had been abandoned and so the first example was also destined to be the last. Nevertheless, it proved the basic concept sound and "ran perfectly for the whole of its 133 hours life."[2]

The work on the RCo.2 was soon put to good use. In October 1952, the Royal Air Force awarded a contract for the Vickers V-1000, a large jet-powered strategic transport that was intended to allow the V bomber force to be supported in the field through air supply only. Vickers also planned on developing a passenger version of the same basic design as the VC-7. The V-1000 design looked like an enlarged de Havilland Comet but from the Valiant it took the wing layout and added a compound sweep (a passing vogue in UK design). It also featured the Comet's wing-embedded engines, demanding an engine with a small cross-section, which limited the amount of bypass the engine could use. It nevertheless required higher power to support a 230,000 pounds (100,000 kg) gross weight, so Rolls responded with the larger RCo.5.

The new engine was similar to the RCo.2 in most ways, differing in details. The low-pressure compressor now had six stages and the high-pressure nine, driven by two and one stage turbines respectively. The first RCo.5 ran in July 1953 and passed an official type rating in August 1955 at 13,000 pounds-force (58,000 N). Construction of the prototype V-1000 was well underway at Vickers Armstrong's Wisley works in the summer of 1955 when the entire project was cancelled. Having second thoughts about the concept of basing the V-bombers away from the UK, the need for the V-1000 became questionable and it became an easy decision to drop the project.

Production versionsEdit

 
Rolls-Royce Conway low bypass turbofan from a Boeing 707.

The Conway was saved once again when it was selected to power the Handley Page Victor B.2 variant, replacing the Armstrong Siddeley Sapphire used by earlier models. For this role, Rolls-Royce designed an even larger model, the RCo.8 of 14,500 pounds-force (64,000 N), which ran for the first time in January 1956. However the RCo.8 was skipped over after receiving a request from Trans-Canada Airlines (TCA) to explore a Conway-powered Boeing 707 or Douglas DC-8, having interested both companies in the idea. Rolls-Royce responded by designing an even larger model of the Conway, the 16,500 pounds-force (73,000 N) RCo.10 and offering the similar military-rated RCo.11 for the Victor. The new engine differed from the RCo.8 in having a new "zeroth stage" at the front of the low-pressure compressor, further increasing cold airflow around the engine. The RCo.10 first flew in the modified prototype Avro Vulcan VX770 on 9 August 1957 only for the aircraft to be lost in a crash the following year. The RCo.11 was flown in the Victor on 20 February 1959.

Boeing calculated that the Conway with a bypass of only 30% would increase the proposed 707-420's range by 8% above the otherwise identical 707-320 powered by Pratt & Whitney JT4A (J75) turbojets. That estimate proved optimistic; the actual range improvement was a maximum of 2%.[3] In May 1956, TCA ordered Conway-powered DC-8-40s, followed by additional orders from Alitalia and Canadian Pacific Air Lines, while the Conway-powered 707-420 was ordered by BOAC, Lufthansa, Varig, El Al and Air India.[4] RCo.10's development was so smooth that after delivering a small number for testing, production deliveries switched to the 17,500-pound-force (78,000 N) RCo.12, which was designed, built and tested before the airframes finished testing. Boeing's 707-420 featured a distinctive, scalloped exhaust nozzle (pictured above) incorporating noise suppression and mechanical and aerodynamic thrust reversal up to 50%, which was developed and supplied by Rolls-Royce.[5] Douglas developed the DC-8's reverser-suppressor nozzle to work in conjunction with a variable ejector, which provided necessary, additional noise suppression.[6]

Although successful in this role, only 37 707s and 32 DC-8s were fitted with the Conway, due largely to delivery of the first US-built bypass engine, the Pratt & Whitney JT3D. Nevertheless, the Conway was successful on those aircraft, and was the first commercial aero engine to be awarded an operational period of up to 10,000 hours between major overhauls.[7] Due to the Conway, B707-420 take-offs were the loudest by jetliners on airports and over communities until Concorde entered service.[8] However, the Conway was revolutionary, being the first turbofan, and the first commercial engine, equipped with internally air-cooled turbine blades, which partially accounted for its high efficiency and an extremely high exhaust temperature of 1,247 °F (675 °C).[9]

Final versionsEdit

Final development of the Conway first involved the RCo.42, designed specifically for the Vickers VC10. As the need for wing-embedded engines was long abandoned by this point, Rolls-Royce dramatically increased the zero-stage diameter to increase the bypass from about 30% to 60%. Other major revisions were incorporated, primarily in the low-pressure compressor. First run was in March 1961. Takeoff rating was 20,370 pounds-force (90,600 N). For the Super VC10, the last model was the RCo.43, rated at 21,800 pounds-force (97,000 N).[10]

DesignEdit

The RCo.12 Conway was an axial-flow turbofan with a low bypass of about 30% or bypass ratio of 0.3:1. It had a seven-stage low-pressure compressor, the first six stages made of aluminium and the last of titanium. Behind this was the nine-stage high-pressure compressor, the first seven stages of titanium and the last two of steel. The bypass housing duct was also made of titanium. The bypass duct started after the seventh stage.[11] The combustion area consisted of ten cannular flame cans. The high-pressure compressor was driven by a single-stage turbine using hollow air-cooled blades, which was followed by the two-stage turbine powering the low-pressure compressor.[12] Accessories were arranged around the front of the engine to minimise overall diameter.

The RCo.12 produced 17,500 pounds-force (78,000 N) for takeoff, weighed 4,544 pounds (2,061 kg) dry and had a specific fuel consumption of 0.725 at takeoff and 0.874 for typical cruise.

In 1968, Hyfil carbon-fibre fan blades were installed on Conways of VC10s operated by BOAC.[13]

Patent disputeEdit

In November 1966, a French manufacturer of steam turbines and automobile superchargers, Société pour l’exploitation des appareils Rateau of La Courneuve, sued Rolls Royce in London for patent infringement, claiming that its 1939 patent for intake design had been copied in the Avon, Conway and Spey models. After a long and keenly-argued hearing, the court determined that the claim was "speculative" because, by 1939, no axial-flow aircraft jet engine had been built [14] and that earlier patents from Frank Whittle and others had already considered the design of the intakes.[15][16]

VariantsEdit

RCo.2
RCo.3
RCo.5
RCo.7
RCo.8
RCo.10
RCo.11
RCo.12
RCo.14
RCo.15
RCo.17
RCo.42
RCo.42/1
RCo.43
Conway 103
(RCo.11)
Conway 505
(RCo.10)
Conway 507
(RCo.10)

ApplicationsEdit

Engines on displayEdit

 
Rolls-Royce Conway

Specifications (Conway RCo.12)Edit

Data from Jane's All The World's Aircraft 1969-70[17]

General characteristics

  • Type: Turbofan
  • Length: 132.4 in (3,360 mm)
  • Diameter: 42 in (1,100 mm)
  • Dry weight: 4,544 lb (2,061 kg)

Components

  • Compressor: dual axial flow; 7-stage LP, 9-stage HP
  • Combustors: cannular steel with 10 Nimonic flames tubes
  • Turbine: axial flow; 1-stage HP (Nimonic air-cooled blades), 2-stage LP
  • Oil system: Wet sump type

Performance

See alsoEdit

ReferencesEdit

  1. ^ http://www.flightglobal.com/pdfarchive/view/1954/1954%20-%200985.html
  2. ^ Kay, pp.113
  3. ^ Francillon, Rene (1999). Boeing 707: pioneer jetliner. Osceola, Wisconsin: MBI Publishing Co. ISBN 0-7603-0675-3.
  4. ^ Kay, pp.114
  5. ^ Jane's All The World's Aircraft 1960-61. London, England.
  6. ^ Waddington, Terry (1996). Douglas DC-8. Great Airliners Series, Volume Two. Miami, Florida: World Transport Press. ISBN 0-9626730-5-6.
  7. ^ Rolls-Royce, a century of innovation [https://web.archive.org/web/20061019202740/http://100.rolls-royce.com/products/view.jsp?id=393 Archived 19 October 2006 at the Wayback Machine
  8. ^ Measured or Estimated (Uncertificated) Airplane Noise Levels. Advisory Circular 36-2B, 9/6/84. Federal Aviation Administration, Washington, DC. Sideline + Flyover Noise (EPNdB): B707-420=228; Super VC10=224; B707-120=222; DC8-40=219.
  9. ^ Type Certificate Data Sheet No. E-308, Revision 10. Rolls Royce Conway. January 5, 1967. Federal Aviation Agency, Washington, DC.
  10. ^ Jane's All The World's Aircraft 1969-70. London, England.
  11. ^ "R-R Conway 1". www.enginehistory.org. Retrieved 21 January 2017.
  12. ^ http://www.flightglobal.com/pdfarchive/view/1960/1960%20-%200077.html
  13. ^ http://www.flightglobal.com/pdfarchive/view/1968/1968%20-%202107.html?search=rolls-royce%20rb211%20hyfil
  14. ^ Note; the first axial-flow jet engines were the German BMW 003 (1940), the Jumo 004 (1940), and the British Metropolitan-Vickers F.2 (1941). The first Rolls-Royce axial-flow engine, the Avon, first ran in 1945. The first French axial-flow engine, the Snecma Atar, first ran in 1948.
  15. ^ "Rateau v. Rolls-Royce—The Judgment". Flight International: 684. 4 May 1967.
  16. ^ Pearson, Harry (1989). Rolls-Royce and the Rateau patents. Derby: Rolls-Royce Heritage Trust. ISBN 0951171089.
  17. ^ Jane's All The World's Aircraft 1969-70. London, England.
  • Gunston, Bill (2006). World Encyclopedia of Aero Engines, 5th Edition. Phoenix Mill, Gloucestershire, England, UK: Sutton Publishing Limited. ISBN 0-7509-4479-X.
  • Kay, Antony, Turbojet, History and Development 1930–1960, Vol 1, Great Britain and Germany, Crowood Press, 2007. ISBN 978-1-86126-912-6

External linksEdit