Open main menu

The impedance analogy is a method of representing a mechanical system by an analogous electrical system. The advantage of doing this is that there is a large body of theory and analysis techniques concerning complex electrical systems, especially in the field of filters.[1] By converting to an electrical representation, these tools in the electrical domain can be directly applied to a mechanical system without modification. A further advantage occurs in electromechanical systems: Converting the mechanical part of such a system into the electrical domain allows the entire system to be analysed as a unified whole.

The mathematical behaviour of the simulated electrical system is identical to the mathematical behaviour of the represented mechanical system. Each element in the electrical domain has a corresponding element in the mechanical domain with an analogous constitutive equation. Every law of circuit analysis, such as Kirchhoff's laws, that apply in the electrical domain also applies to the mechanical impedance analogy.

The impedance analogy is one of the two main mechanical-electrical analogies used for representing mechanical systems in the electrical domain, the other being the mobility analogy. The roles of voltage and current are reversed in these two methods, and the electrical representations produced are the dual circuits of each other. The impedance analogy preserves the analogy between electrical impedance and mechanical impedance whereas the mobility analogy does not. On the other hand, the mobility analogy preserves the topology of the mechanical system when transferred to the electrical domain whereas the impedance analogy does not.

Contents

ApplicationsEdit

The impedance analogy is widely used to model the behaviour of mechanical filters. These are filters that are intended for use in an electronic circuit, but work entirely by mechanical vibrational waves. Transducers are provided at the input and output of the filter to convert between the electrical and mechanical domains.[2]

Another very common use is in the field of audio equipment, such as loudspeakers. Loudspeakers consist of a transducer and mechanical moving parts. Acoustic waves themselves are waves of mechanical motion: of air molecules or some other fluid medium. A very early application of this type was to make significant improvements to the abysmal audio performance of phonographs. In 1929 Edward Norton designed the mechanical parts of a phonograph to behave as a maximally flat filter, thus anticipating the electronic Butterworth filter.[3]

ElementsEdit

Before an electrical analogy can be developed for a mechanical system, it must first be described as an abstract mechanical network. The mechanical system is broken down into a number of ideal elements each of which can then be paired with an electrical analogue.[4] The symbols used for these mechanical elements on network diagrams are shown in the following sections on each individual element.

The mechanical analogies of lumped electrical elements are also lumped elements, that is, it is assumed that the mechanical component possessing the element is small enough that the time taken by mechanical waves to propagate from one end of the component to the other can be neglected. Analogies can also be developed for distributed elements such as transmission lines but the greatest benefits are with lumped element circuits. Mechanical analogies are required for the three passive electrical elements, namely, resistance, inductance and capacitance. What these analogies are is determined by what mechanical property is chosen to represent ''effort'', the analogy of voltage, and the property chosen to represent ''flow'', the analogy of current.[5] In the impedance analogy the effort variable is force and the flow variable is velocity.[6]

ResistanceEdit

 
The mechanical symbol for a damper (left) and its electrical analogy (right).[7] The symbol is meant to be evocative of a dashpot.[8]

The mechanical analogy of electrical resistance is the loss of energy of a moving system through such processes as friction. A mechanical component analogous to a resistor is a shock absorber and the property analogous to resistance is damping. A resistor is governed by the constitutive equation of Ohm's law,

 

The analogous equation in the mechanical domain is,

 
where,
R is resistance
v is voltage
i is current
Rm is mechanical resistance, or damping
F is force
u is velocity induced by the force.[6]

Electrical resistance represents the real part of electrical impedance. Likewise, mechanical resistance is the real part of mechanical impedance.[8]

InductanceEdit

 
The mechanical symbol for a mass (left) and its electrical analogy (right).[7] The square angle below the mass is meant to indicate that movement of the mass is relative to a frame of reference.[9]

The mechanical analogy of inductance in the impedance analogy is mass. A mechanical component analogous to an inductor is a large, rigid weight. An inductor is governed by the constitutive equation,

 

The analogous equation in the mechanical domain is Newton's second law of motion,

 
where,
L is inductance
t is time
M is mass[6]

The impedance of an inductor is purely imaginary and is given by,

 

The analogous mechanical impedance is given by,

 
where,
Z is electrical impedance
j is the imaginary unit
ω is angular frequency
Zm is mechanical impedance.[10]

CapacitanceEdit

 
The mechanical symbol for a stiffness element (left) and its electrical analogy (right).[7] The symbol is meant to be evocative of a spring.[11]

The mechanical analogy of capacitance in the impedance analogy is compliance. It is more common in mechanics to discuss stiffness, the inverse of compliance. The analogy of stiffness in the electrical domain is the less commonly used elastance, the inverse of capacitance.[12] A mechanical component analogous to a capacitor is a spring.[13] A capacitor is governed by the constitutive equation,

 

The analogous equation in the mechanical domain is a form of Hooke's law,

 
where,
D = 1/C is elastance
C is capacitance
S is stiffness

The impedance of a capacitor is purely imaginary and is given by,

 

The analogous mechanical impedance is given by,

 

Alternatively, one can write,

 
where,
Cm = 1/S is mechanical compliance

which is more directly analogous to the electrical expression when capacitance is used.[14]

ResonatorEdit

A mechanical resonator consists of both a mass element and a compliance element. Mechanical resonators are analogous to electrical LC circuits consisting of inductance and capacitance. Real mechanical components unavoidably have both mass and compliance so it is a practical proposition to make resonators as a single component. In fact, it is more difficult to make a pure mass or pure compliance as a single component. A spring can be made with a certain compliance and mass minimised, or a mass can be made with compliance minimised, but neither can be eliminated altogether. Mechanical resonators are a key component of mechanical filters.[15]

GeneratorsEdit

 
The mechanical symbol for a constant force generator (left) and its electrical analogy (right)[16]
 
The mechanical symbol for a constant velocity generator (left) and its electrical analogy (right)[17]

Analogues exist for the active electrical elements of the voltage source and the current source (generators). The mechanical analogue in the impedance analogy of the constant voltage generator is the constant force generator. The mechanical analogue of the constant current generator is the constant velocity generator.[18]

An example of a constant force generator is the constant-force spring. This is analogous to a real voltage source, such as a battery, which remains near constant-voltage with load provided that the load resistance is much higher than the battery internal resistance. An example of a practical constant velocity generator is a lightly loaded powerful machine, such as a motor, driving a belt.[19]

TransducersEdit

Electromechanical systems require transducers to convert between the electrical and mechanical domains. They are analogous to two-port networks and like those can be described by a pair of simultaneous equations and four arbitrary parameters. There are numerous possible representations, but the form most applicable to the impedance analogy has the arbitrary parameters in units of impedance. In matrix form (with the electrical side taken as port 1) this representation is,

 

The element   is the open circuit mechanical impedance, that is, the impedance presented by the mechanical side of the transducer when no current (open circuit) is entering the electrical side. The element  , conversely, is the clamped electrical impedance, that is, the impedance presented to the electrical side when the mechanical side is clamped and prevented from moving (velocity is zero). The remaining two elements,   and  , describe the transducer forward and reverse transfer functions respectively. They are both analogous to transfer impedances and are hybrid ratios of an electrical and mechanical quantity.[20]

TransformersEdit

The mechanical analogy of a transformer is a simple machine such as a pulley or a lever. The force applied to the load can be greater or less than the input force depending on whether the mechanical advantage of the machine is greater or less than unity respectively. Mechanical advantage is analogous to transformer turns ratio in the impedance analogy. A mechanical advantage greater than unity is analogous to a step-up transformer and less than unity is analogous to a step-down transformer.[21]

Power and energy equationsEdit

Table of analogous power and energy equations
Electrical quantity Electrical expression Mechanical analogy Mechanical expression
Energy supplied   Energy supplied  
Power supplied   Power supplied  
Power dissipation in a resistor   Power dissipation in a damper[7]  
Energy stored in an inductor magnetic field   Kinetic energy of a moving mass[22]  
Energy stored in a capacitor electric field   Potential energy stored in a spring[22]  

ExamplesEdit

Simple resonant circuitEdit

 
Simple mechanical resonator (left) and its impedance analogy equivalent circuit (right)

The figure shows a mechanical arrangement of a platform of mass M that is suspended above the substrate by a spring of stiffness S and a damper of resistance R. The impedance analogy equivalent circuit is shown to the right of this arrangement and consists of a series resonant circuit. This system has a resonant frequency, and may have a natural frequency of oscillation if not too heavily damped.[23]

Model of the human earEdit

 
One equivalent circuit of the human ear using the impedance analogy
 
Anatomy of the ear.
  Brown is outer ear.
  Red is middle ear.
  Purple is inner ear.

The circuit diagram shows an impedance analogy model of the human ear. The ear canal section is followed by a transformer representing the eardrum. The eardrum is the transducer between the acoustic waves in air in the ear canal and the mechanical vibrations in the bones of the middle ear. At the cochlea there is another change of medium from mechanical vibrations to the fluid filling the cochlea. This example thus demonstrates the power of electrical analogies in bringing together three domains (acoustic, mechanical and fluid flow) into a single unified whole. If the nerve impulses flowing to the brain had also been included in the model then the electrical domain would have made four domains encompassed in the model.

The cochlea portion of the circuit uses a finite element analysis of the continuous transmission line of the cochlear duct. An ideal representation of such a structure would use infinitesimal elements, and there would thus be an infinite number of them. In this model the cochlea is divided into 350 sections and each section is modelled using a small number of lumped elements.[24]

Advantages and disadvantagesEdit

The principal advantage of the impedance analogy over its alternative, the mobility analogy, is that it maintains the analogy between electrical and mechanical impedance. That is, a mechanical impedance is represented as an electrical impedance and a mechanical resistance is represented as an electrical resistance in the electrical equivalent circuit. It is also natural to think of force as analogous to voltage (generator voltages are often called electromotive force) and velocity as analogous to current. It is this basic analogy that leads to the analogy between electrical and mechanical impedance.[25]

The principal disadvantage of the impedance analogy is that it does not preserve the topology of the mechanical system. Elements that are in series in the mechanical system are in parallel in the electrical equivalent circuit and vice versa.[26]

The impedance matrix representation of a transducer transforms force in the mechanical domain into current in the electrical domain. Likewise, velocity in the mechanical domain is transformed into voltage in the electrical domain. A two-port device that transforms a voltage into an analogous quantity can be represented as a simple transformer. A device that transforms a voltage into an analogue of the dual property of voltage (that is, current, whose analogue is velocity) is represented as a gyrator.[27] Since force is analogous to voltage, not current, this may seem like a disadvantage on the face of it. However, many practical transducers, especially at audio frequencies, work by electromagnetic induction and are governed by just such a relationship.[28] For instance, the force on a current-carrying conductor is given by,

 
where,
B is magnetic flux density
l is length of the conductor

HistoryEdit

The impedance analogy is sometimes called the Maxwell analogy[29] after James Clerk Maxwell (1831–1879) who used mechanical analogies to explain his ideas of electromagnetic fields.[30] However, the term impedance was not coined until 1886 (by Oliver Heaviside),[31] the idea of complex impedance was introduced by Arthur E. Kennelly in 1893, and the concept of impedance was not extended into the mechanical domain until 1920 by Kennelly and Arthur Gordon Webster.[32]

Henri Poincaré in 1907 was the first to describe a transducer as a pair of linear algebraic equations relating electrical variables (voltage and current) to mechanical variables (force and velocity).[33] Wegel, in 1921, was the first to express these equations in terms of mechanical impedance as well as electrical impedance.[34]

ReferencesEdit

  1. ^ Talbot-Smith, p. 1.86
  2. ^ Carr, pp. 170–171
  3. ^ Darlington, p. 7
    • Harrison
  4. ^ Kleiner, pp. 69–70
  5. ^ Busch-Vishniac, p. 20
  6. ^ a b c Talbot-Smith, pp. 1.85–1.86
  7. ^ a b c d Eargle, p. 4
  8. ^ a b Kleiner, p. 71
  9. ^ Kleiner, p. 74
  10. ^ Kleiner, pp. 73–74
  11. ^ Kleiner, p. 73
  12. ^ Pipes & Harvill, p. 187
  13. ^ Kleiner, p. 73
  14. ^ Kleiner, pp. 72–73
  15. ^ Taylor & Huang, pp. 377–383
  16. ^ Kleiner, p. 76
    • Beranek & Mellow, p. 70
  17. ^ Kleiner, p. 77
    • Beranek & Mellow, p. 70
  18. ^ Kleiner, pp. 76–77
  19. ^ Kleiner, p. 77
  20. ^ Jackson, pp. 16–17
    • Paik, p. 572
  21. ^ Kleiner, pp. 74–76
    • Beranek & Mellow, pp. 76–77
  22. ^ a b Talbot-Smith, p. 1.86
  23. ^ Eargle, pp. 3–4
  24. ^ Fukazawa & Tanaka, pp. 191–192
  25. ^ Busch-Vishniac, p. 20
  26. ^ Busch-Vishniac, pp. 20–21
    • Eargle, pp. 4–5
  27. ^ Beranek & Mellow, pp. 70–71
  28. ^ Eargle, pp. 5–7
  29. ^ Busch-Vishniac, p. 20
  30. ^ Stephens & Bate, p. 421
  31. ^ Martinsen & Grimnes, p. 287
  32. ^ Hunt p. 66
  33. ^ Pierce, p. 200, cites Poincaré
  34. ^ Hunt, p. 66
    • Pierce, p. 200, cites Wegel

BibliographyEdit

  • Beranek, Leo Leroy; Mellow, Tim J., Acoustics: Sound Fields and Transducers, Academic Press, 2012 ISBN 0123914213.
  • Busch-Vishniac, Ilene J., Electromechanical Sensors and Actuators, Springer Science & Business Media, 1999 ISBN 038798495X.
  • Carr, Joseph J., RF Components and Circuits, Newnes, 2002 ISBN 0-7506-4844-9.
  • Darlington, S. "A history of network synthesis and filter theory for circuits composed of resistors, inductors, and capacitors", IEEE Transactions on Circuits and Systems, vol. 31, no. 1, pp. 3–13, 1984.
  • Eargle, John, Loudspeaker Handbook, Kluwer Academic Publishers, 2003 ISBN 1402075847.
  • Fukazawa, Tatsuya; Tanaka, Yasuo, "Evoked otoacoustic emissions in a cochlear model", pp. 191–196 in Hohmann, D. (ed), ECoG, OAE and Intraoperative Monitoring: Proceedings of the First International Conference, Würzburg, Germany, September 20–24, 1992, Kugler Publications, 1993 ISBN 9062990975.
  • Harrison, Henry C. "Acoustic device", U.S. Patent 1,730,425, filed 11 October 1927 (and in Germany 21 October 1923), issued 8 October 1929.
  • Hunt, Frederick V., Electroacoustics: the Analysis of Transduction, and its Historical Background, Harvard University Press, 1954 OCLC 2042530.
  • Jackson, Roger G., Novel Sensors and Sensing, CRC Press, 2004 ISBN 1420033808.
  • Kleiner, Mendel, Electroacoustics, CRC Press, 2013 ISBN 1439836183.
  • Martinsen, Orjan G.; Grimnes, Sverre, Bioimpedance and Bioelectricity Basics, Academic Press, 2011 ISBN 0080568807.
  • Paik, H. J., "Superconduction accelerometers, gravitational-wave transducers, and gravity gradiometers", pp. 569–598, in Weinstock, Harold, SQUID Sensors: Fundamentals, Fabrication, and Applications, Springer Science & Business Media, 1996 ISBN 0792343506.
  • Pierce, Allan D., Acoustics: an Introduction to its Physical Principles and Applications, Acoustical Society of America 1989 ISBN 0883186128.
  • Pipes, Louis A.; Harvill, Lawrence R., Applied Mathematics for Engineers and Physicists, Courier Dover Publications, 2014 ISBN 0486779513.
  • Poincaré, H., "Study of telephonic reception", Eclairage Electrique, vol. 50, pp. 221–372, 1907.
  • Stephens, Raymond William Barrow; Bate, A. E., Acoustics and vibrational physics, Edward Arnold, 1966 OCLC 912579.
  • Talbot-Smith, Michael, Audio Engineer's Reference Book, Taylor & Francis, 2013 ISBN 1136119736.
  • Taylor, John; Huang, Qiuting, CRC Handbook of Electrical Filters, CRC Press, 1997 ISBN 0849389518.
  • Wegel, R. L., "Theory of magneto-mechanical systems as applied to telephone receivers and similar structures", Journal of the American Institute of Electrical Engineers, vol. 40, pp. 791–802, 1921.