A watchdog timer (WDT, or simply a watchdog), sometimes called a computer operating properly timer (COP timer),[1] is an electronic or software timer that is used to detect and recover from computer malfunctions. Watchdog timers are widely used in computers to facilitate automatic correction of temporary hardware faults, and to prevent errant or malevolent software from disrupting system operation.

A watchdog timer integrated circuit (Texas Instruments TPS3823). One pin receives the timer restart ("kick"[a]) signal from the computer; another pin outputs the timeout signal.

During normal operation, the computer regularly restarts the watchdog timer to prevent it from elapsing, or "timing out". If, due to a hardware fault or program error, the computer fails to restart the watchdog, the timer will elapse and generate a timeout signal. The timeout signal is used to initiate corrective actions. The corrective actions typically include placing the computer and associated hardware in a safe state and invoking a computer reboot.

Microcontrollers often include an integrated, on-chip watchdog. In other computers the watchdog may reside in a nearby chip that connects directly to the CPU, or it may be located on an external expansion card in the computer's chassis.

Applications edit

Watchdog timers are essential in remote, automated systems such as this Mars Exploration Rover

Watchdog timers are commonly found in embedded systems and other computer-controlled equipment where humans cannot easily access the equipment or would be unable to react to faults in a timely manner. In such systems, the computer cannot depend on a human to invoke a reboot if it hangs; it must be self-reliant. For example, remote embedded systems such as space probes are not physically accessible to human operators; these could become permanently disabled if they were unable to autonomously recover from faults. In robots and other automated machines, a fault in the control computer could cause equipment damage or injuries before a human could react, even if the computer is easily accessed. A watchdog timer is usually employed in cases like these.

Watchdog timers are also used to monitor and limit software execution time on a normally functioning computer. For example, a watchdog timer may be used when running untrusted code in a sandbox, to limit the CPU time available to the code and thus prevent some types of denial-of-service attacks.[2] In real-time operating systems, a watchdog timer may be used to monitor a time-critical task to ensure it completes within its maximum allotted time and, if it fails to do so, to terminate the task and report the failure.

Architecture and operation edit

Restarting edit

Some watchdog timers only allow kicks during a time window. Kicks occurring outside the window have no effect on the timer and may be treated as faults.

The act of restarting a watchdog timer is commonly referred to as kicking[a] the watchdog.[3][4] Kicking is typically done by writing to a watchdog control port or by setting a particular bit in a register. Alternatively, some tightly coupled[b] watchdog timers are kicked by executing a special machine language instruction. An example of this is the CLRWDT (clear watchdog timer) instruction found in the instruction set of some PIC microcontrollers.

In computers that are running operating systems, watchdog restarts are usually invoked through a device driver. For example, in the Linux operating system, a user space program will kick the watchdog by interacting with the watchdog device driver, typically by writing a zero character to /dev/watchdog or by calling a KEEPALIVE ioctl.[5] The device driver, which serves to abstract the watchdog hardware from user space programs, may also be used to configure the time-out period and start and stop the timer.

Some watchdog timers will only allow kicks during a specific time window. The window timing is usually relative to the previous kick or, if the watchdog has not yet been kicked, to the moment the watchdog was enabled. The window begins after a delay following the previous kick, and ends after a further delay. If the computer attempts to kick the watchdog before or after the window, the watchdog will not be restarted, and in some implementations this will be treated as a fault and trigger corrective action.

Enabling edit

Screenshot of wdctl, a program that shows watchdog status

A watchdog timer is said to be enabled when operating and disabled when idle. Upon power-up, a watchdog may be unconditionally enabled or it may be initially disabled and require an external signal to enable it. In the latter case, the enabling signal may be automatically generated by hardware or it may be generated under software control.

When automatically generated, the enabling signal is typically derived from the computer reset signal. In some systems the reset signal is directly used to enable the watchdog. In others, the reset signal is delayed so that the watchdog will become enabled at some later time following the reset. This delay allows time for the computer to boot before the watchdog is enabled. Without this delay, the watchdog would timeout and invoke a subsequent reset before the computer can run its application software — the software which kicks the watchdog — and the system would become stuck in an endless cycle of incomplete reboots.

Single-stage watchdog edit

Watchdog timers come in many configurations, and many allow their configurations to be altered. For example, the watchdog and CPU may share a common clock signal as shown in the block diagram below, or they may have independent clock signals. A basic watchdog timer has a single timer stage which, upon timeout, typically will reset the CPU:


Multistage watchdog edit

Two or more timers are sometimes cascaded to form a multistage watchdog timer, where each timer is referred to as a timer stage, or simply a stage. For example, the block diagram below shows a three-stage watchdog. In a multistage watchdog, only the first stage is kicked by the processor. Upon first stage timeout, a corrective action is initiated and the next stage in the cascade is started. As each subsequent stage times out, it triggers a corrective action and starts the next stage. Upon final stage timeout, a corrective action is initiated, but no other stage is started because the end of the cascade has been reached. Typically, single-stage watchdog timers are used to simply restart the computer, whereas multistage watchdog timers will sequentially trigger a series of corrective actions, with the final stage triggering a computer restart.[4]


Time intervals edit

Watchdog timers may have either fixed or programmable time intervals. Some watchdog timers allow the time interval to be programmed by selecting from among a few selectable, discrete values. In others, the interval can be programmed to arbitrary values. Typically, watchdog time intervals range from ten milliseconds to a minute or more. In a multistage watchdog, each timer may have its own, unique time interval.

Corrective actions edit

A watchdog timer may initiate any of several types of corrective action, including maskable interrupt, non-maskable interrupt, hardware reset, fail-safe state activation, power cycling, or combinations of these. Depending on its architecture, the type of corrective action or actions that a watchdog can trigger may be fixed or programmable. Some computers (e.g., PC compatibles) require a pulsed signal to invoke a hardware reset. In such cases, the watchdog typically triggers a hardware reset by activating an internal or external pulse generator, which in turn creates the required reset pulses.[4]

In embedded systems and control systems, watchdog timers are often used to activate fail-safe circuitry. When activated, the fail-safe circuitry forces all control outputs to safe states (e.g., turns off motors, heaters, and high-voltages) to prevent injuries and equipment damage while the fault persists. In a two-stage watchdog, the first timer is often used to activate fail-safe outputs and start the second timer stage; the second stage will reset the computer if the fault cannot be corrected before the timer elapses.

Watchdog timers are sometimes used to trigger the recording of system state information—which may be useful during fault recovery[4]—or debug information (which may be useful for determining the cause of the fault) onto a persistent medium. In such cases, a second timer—which is started when the first timer elapses—is typically used to reset the computer later, after allowing sufficient time for data recording to complete. This allows time for the information to be saved, but ensures that the computer will be reset even if the recording process fails.


For example, the above diagram shows a likely configuration for a two-stage watchdog timer. During normal operation the computer regularly kicks Stage1 to prevent a timeout. If the computer fails to kick Stage1 (e.g., due to a hardware fault or programming error), Stage1 will eventually timeout. This event will start the Stage2 timer and, simultaneously, notify the computer (by means of a non-maskable interrupt) that a reset is imminent. Until Stage2 times out, the computer may attempt to record state information, debug information, or both. As a last resort, the computer will be reset upon Stage2 timeout.

Fault detection edit

A watchdog timer provides automatic detection of catastrophic malfunctions that prevent the computer from kicking it. However, computers often have other, less-severe types of faults which do not interfere with kicking, but which still require watchdog oversight. To support these, a computer system is typically designed so that its watchdog timer will be kicked only if the computer deems the system functional. The computer determines whether the system is functional by conducting one or more fault detection tests and will kick the watchdog only if all tests have passed.[citation needed]

In computers that are running an operating system and multiple processes, a single, simple test might be insufficient to guarantee normal operation, as it could fail to detect a subtle fault condition and therefore allow the watchdog to be kicked even though a fault condition exists. For example, in the case of the Linux operating system, a user-space watchdog daemon may simply kick the watchdog periodically without performing any tests. As long as the daemon runs normally, the system will be protected against serious system crashes such as a kernel panic. To detect less severe faults, the daemon[6] can be configured to perform tests that cover resource availability (e.g., sufficient memory and file handles, reasonable CPU time), evidence of expected process activity (e.g., system daemons running, specific files being present or updated), overheating, and network activity, and system-specific test scripts or programs can also be run.[7]

Upon discovery of a failed test, the computer may attempt to perform a sequence of corrective actions under software control, culminating with a software-initiated reboot. If the software fails to invoke a reboot, the watchdog timer will timeout and invoke a hardware reset. In effect, this is a multistage watchdog timer in which the software comprises the first and intermediate timer stages and the hardware reset the final stage. In a Linux system, for example, the watchdog daemon could attempt to perform a software-initiated restart, which can be preferable to a hardware reset as the file systems will be safely unmounted and fault information will be logged. It is essential, however, to have the insurance provided by a hardware timer, since a software restart can fail under a number of fault conditions.[citation needed]

See also edit

Notes edit

  1. ^ a b Various terms are used for the act of restarting a watchdog timer. Some (e.g. kick, pet, feed, tickle) draw a connection to guard dogs, whereas others (e.g. tag, ping, reset) do not. This article uses kick for consistency.
  2. ^ A tightly coupled watchdog timer is effectively a built-in extension of the processor and, as such, may be accessed by special machine language instructions which are specific to it.

References edit

  1. ^ "4.11 Dual Staged Watchdog Timer". Kontron User's Guide - COMe-cBTi6R. Document Revision 1.0. Kontron. 2021. Archived from the original on 2023-09-23. Retrieved 2023-09-23. p. 39: A watchdog timer (or computer operating properly (COP) timer) is a computer hardware or software timer that triggers a system reset or other corrective action if the main program, due to some fault condition, such as a hang, neglects to regularly service the watchdog (writing a "service pulse" to it, also referred to as "kicking the dog", "petting the dog", "feeding the watchdog" or "triggering the watchdog"). The intention is to bring the system back from the nonresponsive state into normal operation.
  2. ^ "The Grenade Timer: Fortifying the Watchdog Timer Against Malicious Mobile Code" by Frank Stajano and Ross Anderson (2000).
  3. ^ Murphy, Niall & Barr, Michael (October 2001). "Watchdog Timers". Embedded Systems Programming. Retrieved 18 February 2013.
  4. ^ a b c d Lamberson, Jim. "Single and Multistage Watchdog Timers" (PDF). Sensoray. Retrieved 10 September 2013.
  5. ^ Weingel, Christer. "The Linux Watchdog driver API". Retrieved 20 January 2021.
  6. ^ "Watchdog 'man' page". Retrieved 2013-09-10.
  7. ^ Crawford, Paul (2013-09-05). "Linux Watchdog - General Tests". Archived from the original on 2013-09-14. Retrieved 2013-09-10.

Further reading edit

External links edit