Properties of waterEdit
Underwater explosions differ from in-air explosions due to the properties of water:
- Mass and incompressibility (all explosions) – water has a much higher density than air, which makes water harder to move (higher inertia). It is also relatively hard to compress (increase density) when under pressure in a low range, say up to 100 atmospheres. These two together make water an excellent conductor of shock waves from an explosion.
- Effect of neutron exposure on salt water (nuclear explosions only) – most underwater blast scenarios happen in seawater, not fresh or pure water. The water itself is not much affected by neutrons but salt is strongly affected. When exposed to neutron radiation during the microsecond of active detonation of a nuclear pit, water itself does not typically "activate", or become radioactive. The two atoms in water, hydrogen and oxygen, can absorb an extra neutron, becoming deuterium and oxygen-17 respectively, both of which are stable isotopes. Even oxygen-18 is stable. Radioactive atoms can result if a hydrogen atom absorbs two neutrons, an oxygen atom absorbs three neutrons, or oxygen-16 undergoes a high energy neutron (n-p) reaction to produce a short lived nitrogen-16. In any typical scenario the probability of such multiple capture in significant numbers in the short time of active nuclear reactions around a bomb are very low. They are somewhat greater when the water is continuously irradiated, as in the closed loop of a nuclear reactor.
Salt in seawater readily absorbs neutrons into both the sodium-23 and chlorine-35 atoms, which change to radioactive isotopes. Sodium-24 has a half-life of about 15 hours, while that of chlorine-36 (which has a lower activation cross-section) is 300,000 years. The sodium is the most dangerous contaminant after the explosion because it has a short half-life. These are generally the main radioactive contaminants in an underwater blast; others are the usual blend of irradiated minerals, coral, unused nuclear fuel, and bomb case components present in a surface blast nuclear fallout, carried in suspension or dissolved in the water. Plain distillation or evaporating water (clouds, humidity, and precipitation) removes radiation contamination, leaving behind the radioactive salt.
Underwater explosions are categorized by the depth of the explosion. Shallow underwater explosions are those where a crater formed at the water's surface is large in comparison with the depth of the explosion. Deep underwater explosions are those where the crater is small in comparison with the depth of the explosion, or nonexistent.
The overall effect of an underwater explosion depends on depth, the size and nature of the explosive charge, and the presence, composition and distance of reflecting surfaces such as the seabed, surface, thermoclines, etc. This phenomenon has been extensively used in antiship warhead design since an underwater explosion (particularly one underneath a hull) can produce greater damage than an above-surface one of the same explosive size. Initial damage to a target will be caused by the first shockwave; this damage will be amplified by the subsequent physical movement of water and by the repeated secondary shockwaves or bubble pulse. Additionally, charge detonation away from the target can result in damage over a larger hull area.
Underwater nuclear tests close to the surface can disperse radioactive water and steam over a large area, with severe effects on marine life, nearby infrastructures and humans. The detonation of nuclear weapons underwater was banned by the 1963 Partial Nuclear Test Ban Treaty and it is also prohibited under the Comprehensive Nuclear-Test-Ban Treaty of 1996.
Shallow underwater explosionEdit
The Baker nuclear test at Bikini Atoll in July 1946 was a shallow underwater explosion, part of Operation Crossroads. A 20 kiloton warhead was detonated in a lagoon which was approximately 200 ft (61 m) deep. The first effect was illumination of the water because of the underwater fireball. A rapidly expanding gas bubble created a shock wave that caused an expanding ring of apparently dark water at the surface, called the slick, followed by an expanding ring of apparently white water, called the crack. A mound of water and spray, called the spray dome, formed at the water's surface which became more columnar as it rose. When the rising gas bubble broke the surface, it created a shock wave in the air as well. Water vapor in the air condensed as a result of a Prandtl-Glauert singularity, making a spherical cloud that marked the location of the shock wave. Water filling the cavity formed by the bubble caused a hollow column of water, called the chimney or plume, to rise 6,000 ft (1,800 m) in the air and break through the top of the cloud. A series of ocean surface waves moved outward from the center. The first wave was about 94 ft (29 m) high at 1,000 ft (300 m) from the center. Other waves followed, and at further distances some of these were higher than the first wave. For example, at 22,000 ft (6,700 m) from the center, the ninth wave was the highest at 6 ft (1.8 m). Gravity caused the column to fall to the surface and caused a cloud of mist to move outward rapidly from the base of the column, called the base surge. The ultimate size of the base surge was 3.5 mi (5.6 km) in diameter and 1,800 ft (550 m) high. The base surge rose from the surface and merged with other products of the explosion, to form clouds which produced moderate to heavy rainfall for nearly one hour.
Deep underwater explosionEdit
An example of a deep underwater explosion is the Wahoo test, which was carried out in 1958 as part of Operation Hardtack I. A 9 kt Mk-7 was detonated at a depth of 500 ft (150 m) in deep water. There was little evidence of a fireball. The spray dome rose to a height of 900 ft (270 m). Gas from the bubble broke through the spray dome to form jets which shot out in all directions and reached heights of up to 1,700 ft (520 m). The base surge at its maximum size was 2.5 mi (4.0 km) in diameter and 1,000 ft (300 m) high.
The heights of surface waves generated by deep underwater explosions are greater because more energy is delivered to the water. During the Cold War, underwater explosions were thought to operate under the same principles as tsunamis, potentially increasing dramatically in height as they move over shallow water, and flooding the land beyond the shoreline. Later research and analysis suggested that water waves generated by explosions were different from those generated by tsunamis and landslides. Méhauté et al. conclude in their 1996 overview Water Waves Generated by Underwater Explosion that the surface waves from even a very large offshore undersea explosion would expend most of their energy on the continental shelf, resulting in coastal flooding no worse than that from a bad storm.
The Operation Wigwam test in 1955 occurred at a depth of 2,000 ft (610 m), the deepest detonation of any nuclear device.
Deep nuclear explosionEdit
- Note: This section is based on Analysis of various models of underwater nuclear explosions (1971).
Unless it breaks the water surface while still a hot gas bubble, an underwater nuclear explosion leaves no trace at the surface but hot, radioactive water rising from below. This is always the case with explosions deeper than about 2,000 ft (610 m).
During such an explosion, the hot gas bubble quickly collapses because:
- The water pressure is enormous deeper than 2,000 feet.
- The expansion reduces gas pressure, which decreases temperature.
- Rayleigh–Taylor instability at the gas/water boundary causes "fingers" of water to extend into the bubble, increasing the boundary surface area.
- Water is incompressible.
- Vast amounts of energy are absorbed by phase change (water becomes steam at the boundary).
- Expansion quickly becomes unsustainable because the amount of water pushed outward increases with the cube of the blast-bubble radius.
Since water is not readily compressible, moving this much of it out of the way so quickly absorbs a massive amount of energy—all of which comes from the pressure inside the expanding bubble. Eventually, the water pressure outside the bubble causes it to collapse back into a small sphere and then rebound, expanding again. This is repeated several times, but each rebound contains only about 40% of the energy of the previous cycle. At its maximum diameter (during the first oscillation), a very large nuclear bomb exploded in very deep water creates a bubble about a half-mile wide in about one second, and then contracts (which also takes one second).
Blast bubbles from deep nuclear explosions become mere hot water in about six seconds and leave no "regular" bubbles to float up to the surface. This is sooner than blast bubbles from conventional explosives.
This drastic loss of energy between cycles is caused in part by the extreme force of a nuclear explosion pushing the bubble wall outward supersonically (faster than the speed of sound in saltwater). This causes Rayleigh–Taylor instability. That is, the smooth inner wall surface becomes turbulent and fractal, with fingers and branches of cold ocean water extending into the bubble. That cold water cools the hot gas inside and causes it to condense. The bubble becomes less of a sphere and looks more like the Crab Nebula, the deviation of which from a smooth surface is also due to Rayleigh–Taylor instability.
As one might expect, large, shallow explosions expand faster than deep, small ones.
Deep explosions have longer oscillations.
The water pressure just outside the bubble varies dramatically.
Despite being in direct contact with a nuclear explosion, the water of the expanding bubble wall does not boil. This is because the pressure inside the bubble exceeds (by far) the vapor pressure of ocean water. The water touching the blast can only boil during contraction. This boiling is like evaporation, cooling the bubble wall, and it is another reason that an oscillating blast bubble contains only 40% of the energy it had in the previous cycle.
During these hot gas oscillations, the bubble continually rises ("migrates") for the same reason a mushroom cloud rises: it is less dense. This causes the blast bubble never to be perfectly spherical. Instead, the bottom of the bubble is flatter, and during contraction, it even tends to "reach up" toward the blast center. In the last contraction cycle, the bottom of the bubble touches the top before the sides have fully collapsed, and the bubble becomes a torus in its last second of life. After that, all that remains of a large nuclear explosion is a mass of hot water, slowly rising and rapidly cooling through the near-freezing water in the deep ocean.
List of underwater nuclear testsEdit
Relatively few underwater nuclear tests were performed before they were banned by the Partial Test Ban Treaty. They are:
|Test series||Name||Nation||Date (UT)||Location||Bomb depth, depth of water||Yield||Notes|
|Crossroads||Baker||US||July 25, 1946||Bikini Atoll, PPG||50 m (160 ft), 100 m (330 ft)||20 kt||Probe the effects of a shallow underwater nuclear bomb on various surface fleet units.|
|Wigwam||Wigwam||US||May 14, 1955||North Pacific Ocean||610 m (2,000 ft), 4,880 m (16,010 ft)||30 kt||A Mark 90-B7 "Betty" nuclear depth charge test to determine specifically submarine vulnerability to deep atomic depth charges.|
|1955||22 (Joe 17)||USSR||September 21, 1955||Chernaya Bay, Novaya Zemlya||10 m (33 ft), 10 m (33 ft)||3.5 kt||Test of atomic torpedo.|
|1957||48||USSR||October 10, 1957||Novaya Zemlya||30 m (98 ft), unknown||10 kt||A T-5 torpedo test.|
|Hardtack I||Wahoo||US||May 16, 1958||Outside Enewetak Atoll, PPG||150 m (490 ft), 980 m (3,220 ft)||9 kt||Test of a deep water bomb against ship hulls.|
|Hardtack I||Umbrella||US||June 8, 1958||Inside Enewetak Atoll, PPG||50 m (160 ft), 50 m (160 ft)||9 kt||Test of a shallow water bomb on floor against ship hulls.|
|1961||122 (Korall-1)||USSR||October 23, 1961||Novaya Zemlya||20 m (66 ft), unknown||4.8 kt||A T-5 torpedo test.|
|Dominic||Swordfish||US||May 11, 1962||Pacific Ocean, near Johnston Island||198 m (650 ft), 1,000 m (3,300 ft)||<20 kt||Test of the RUR-5 ASROC system.|
Note: it is often believed that the French did extensive underwater tests in French West Polynesia on the Moruroa and Fangataufa Atolls. This is incorrect; the bombs were placed in shafts drilled into the underlying coral and volcanic rock, and they did not intentionally leak fallout.
Underwater Nuclear Detonation Detection via HydroacousticsEdit
There are several methods of detecting nuclear detonations. Hydroacoustics is the primary means of determining if a nuclear detonation has occurred underwater. Hydrophones are used to monitor the change in water pressure as sound waves propagate through the world's oceans. Sound travels through 20 °C water at approximately 1482 meters per second, compared to the 332 m/s speed of sound through air. In the world's oceans, sound travels most efficiently at a depth of approximately 1000 meters. Sound waves that travel at this depth travel at minimum speed and are trapped in a layer known as the Sound Fixing and Ranging Channel (SOFAR). Sounds can be detected in the SOFAR from large distances, allowing for a limited number of monitoring stations required to detect oceanic activity. Hydroacoustics was originally developed in the early 20th century as a means of detecting objects like icebergs and shoals to prevent accidents at sea.
Three hydroacoustic stations were built before the adoption of the Comprehensive Nuclear-Test-Ban Treaty. Two hydrophone stations were built in the North Pacific Ocean and Mid-Atlantic Ocean, and a T-phase station was built off the west coast of Canada. When the CTBT was adopted, 8 more hydroacoustic stations were constructed to create a comprehensive network capable of identifying underwater nuclear detonations anywhere in the world. These 11 hydroacoustic stations, in addition to 326 monitoring stations and laboratories, comprise the International Monitoring System (IMS), which is monitored by the Preparatory Commission for the Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO).
There are two different types of hydroacoustic stations currently used in the IMS network; 6 hydrophone monitoring stations and 5 T-phase stations. These 11 stations are primarily located in the southern hemisphere, which is primarily ocean. Hydrophone monitoring stations consist of an array of three hydrophones suspended from cables tethered to the ocean floor. They are positioned at a depth located within the SOFAR in order to effectively gather readings. Each hydrophone records 250 samples per second, while the tethering cable supplies power and carries information to the shore. This information is converted to a usable form and transmitted via secure satellite link to other facilities for analysis. T-phase monitoring stations record seismic signals generate from sound waves that have coupled with the ocean floor or shoreline. T-phase stations are generally located on steep-sloped islands in order to gather the cleanest possible seismic readings. Like hydrophone stations, this information is sent to the shore and transmitted via satellite link for further analysis. Hydrophone stations have the benefit of gathering readings directly from the SOFAR, but are generally more expensive to implement than T-phase stations. Hydroacoustic stations monitor frequencies from 1 to 100 Hertz to determine if an underwater detonation has occurred. If a potential detonation has been identified by one or more stations, the gathered signals will contain a high bandwidth with the frequency spectrum indicating an underwater cavity at the source.
- Le Méhauté, Bernard; Wang, Shen (1995). Water waves generated by underwater explosion. World Scientific Publishing. ISBN 981-02-2083-9.
- RMCS Precis on Naval Ammunition, Jan 91
- "'Test Baker', Bikini Atoll". CTBTO Preparatory Commission. Retrieved 31 May 2012.
- "Is it possible to test a nuclear weapon without producing radioactive fallout?". How stuff works. Retrieved 31 May 2012.
- Glasstone, Samuel; Dolan, Philip (1977). "Descriptions of nuclear explosions". The effects of nuclear weapons (Third ed.). Washington: U.S. Department of Defense; Energy Research and Development Administration.
- Glasstone, Samuel; Dolan, Philip (1977). "Shock effects of surface and subsurface bursts". The effects of nuclear weapons (third ed.). Washington: U.S. Department of Defense; Energy Research and Development Administration.
- Everything in the "dynamics" section is from Analysis of various models of underwater nuclear explosions (1971), U.S. Department of Defense
- "Hydroacoustic monitoring: CTBTO Preparatory Commission". www.ctbto.org. Retrieved 2017-04-24.
- "How fast does sound travel?". www.indiana.edu. Retrieved 2017-04-24.
- "Untitled Document". www.le.ac.uk. Retrieved 2017-04-24.
- Australia, c\=AU\;o\=Australia Government\;ou\=Geoscience (2014-05-15). "Hydroacoustic Monitoring". www.ga.gov.au. Retrieved 2017-04-24.
- "Overview of the verification regime: CTBTO Preparatory Commission". www.ctbto.org. Retrieved 2017-04-24.
- "ASA/EAA/DAGA '99 - Hydroacoustic Monitoring for the Comprehensive Nuclear-Test-Ban Treaty". acoustics.org. Retrieved 2017-04-25.
- Monitoring, Government of Canada, Natural Resources Canada, Nuclear Explosion. "IMS Hydroacoustic Network". can-ndc.nrcan.gc.ca. Retrieved 2017-04-25.
- Glasstone, Samuel; Dolan, Philip (1977). The effects of nuclear weapons (third ed.). Washington: U.S. Department of Defense; Energy Research and Development Administration.
- Le Méhauté, Bernard; Wang, Shen (1995). Water waves generated by underwater explosion. Advanced Series on Ocean Engineering. 10. World Scientific Publishing. ISBN 981-02-2083-9.