Where's the equation relating thermal mass to temperature and heat transfer rate? Mollwollfumble (talk) 06:35, 23 June 2009 (UTC)Reply

To those in the know, the equation is obvious from the units. For those not in the know, I've added the equation, based on the one in specific heat capacity. (Although, note that thermal mass relates temperature and heat transfer, not heat transfer rate - you may be looking for something like Newton's law of cooling, which is related to thermal conductivity.) ― Darekun (talk) 13:46, 27 July 2009 (UTC)Reply

Thermal flywheel effect merge

edit

Since there hasn't been any discussion on the merge in the months since it was tagged, and Thermal flywheel effect was simply a mention of thermal mass or specific heat capacity as applied to buildings (which this article is already mostly about), I performed the merge. Most of the information there either duplicated information here or was added, but this list of relative specific heat capacities is only partially duplicated:

Materials, higher to lower "flywheel effect"

  1. Packed Earth
  2. Brick
  3. Water
  4. Hardwood lumber or timbers
  5. Softwood & construction lumber
  6. Steel
  7. Insulation
  8. Air
  9. Aluminum

Darekun (talk) 13:46, 27 July 2009 (UTC)Reply

Now how about either a merge with heat capacity or a clearer distinction from it? This article says "Not to be confused with Heat capacity" at the top, but then immediately goes on to say that that's exactly what it's about. Not R (talk) 20:10, 2 December 2010 (UTC)Reply

this article appears building material specific. Thermal Mass is used throughout engineering and espeically when designing ovens, heat curing systems, and cooling systems. i.e. solder reflow ovens, adhesive cure ovens, post-process cooling etc. 74.198.8.57 (talk) 18:03, 3 February 2011 (UTC)ShawnReply

Thermal "flywheel, mass, and inertia" are misnomers

edit

I object to the phrases "providing 'inertia' against temperature fluctuations", "the thermal flywheel effect" and "thermal mass". Since the energy is indeed stored in the mass of these materials it is tempting to call it thermal mass. But when we think of mass, we also think of inertia, a property which does not exist in the thermal domain. There is no such thing as a thermal flywheel. By this I mean that in a thermal system, in order for heat to flow there must be a temperature difference. But as soon as that difference is removed, the flow stops. The flow has no inertia. As we know, energy can be stored in physical systems in either potential or kinetic form. In the mechanical domain, Kinetic energy is what is stored in a flywheel or a moving mass and potential energy is what is stored in a spring. The kinetic energy is determined by the speed of the flywheel or the mass. The potential energy is determined by the force in the spring. When the force is removed from a mass, the mass keeps going. In the thermal domain, there is only potential energy storage, the amount of energy stored being determined by the temperature of the substance it is stored in. Thus it acts more like a spring than a mass or flywheel. Or like a capacitor in the electrical domain than an inductor. Thus I feel that "thermal mass" and "thermal flywheel" are misleading terms that we should endeavor to eliminate. The better term is "thermal capacitance". Unfortunately these misleading terms are in wide usage, so perhaps we should at least explain the misnomer and point out that they are potential energy storage effects not kinetic energy storage effects as implied by "mass", "inertia" and "flywheel". JDHeinzmann (talk) 14:51, 1 July 2020 (UTC)Reply

Hi -- I know your comment is four years old, but I agree completely. In particular, in science the word "mass" applies to one and only one property of matter, it's resistance to acceleration when a force is applied to it. While there are categories of mass -- sprung vs unsprung, or relativistic -- they still apply to the same property of matter. The term "thermal mass" implies that there are different kinds of mass. There aren't.
I would quibble that "thermal capacitance" isn't quite right, "capacitance" has a specific meaning that isn't what we're talking about. I'd say "capacity" is a better word. "Thermal" can be problematic because it is used to refer to both heat and temperature, and distinguishing between them is something that beginning physics students are taught. So I would argue that "heat capacity" is the proper term.
Coincidentally, that is the term that scientists use. DC Contrarian (talk) 23:15, 28 July 2024 (UTC)Reply
edit

Hello fellow Wikipedians,

I have just modified one external link on Thermal mass. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 13:52, 22 January 2018 (UTC)Reply