Ka-Bar (trademarked as KA-BAR, pronounced /
|(USMC) Knife, Fighting Utility (USN Mark 2 utility knife)|
Commemorative USMC Ka-Bar knife
|Place of origin||United States|
|Used by||United States Marine Corps|
United States Navy
United States Army
|Wars||World War II|
Invasion of Grenada
Operation Just Cause
War in Afghanistan
|Designed||23 November 1942|
|Manufacturer||Camillus Cutlery Co.|
Union Cutlery Co.
Pal Cutlery Co.
Robeson (ShurEdge) Cutlery Co.
Ontario Knife Co.
|Mass||0.7 pounds (320 g)|
|Length||11 7⁄8 inches (30.16 cm)|
|Blade length||7 inches (18 cm)|
|Blade type||clip point|
|Hilt type||Stacked leather washers|
|Scabbard/sheath||Leather (USMC) or plastic (USN)|
Although Ka-Bar Knives, Inc. currently makes a wide variety of knives and cutlery, it is best known for the Ka-Bar Fighting/Utility knife, which has traditionally used a 7 inches (17.8 cm) 1095 carbon steel clip point blade and leather-washer handle.
The originator of the KA-BAR trademark, the Union Cutlery Co. of Olean, New York, began using the name on its knives and advertising in 1923, having received a letter from a fur trapper who had used the knife to kill a wounded bear which attacked him when his rifle jammed. According to company records, the letter was only partially legible; "ka bar" could be read, as fragments of the phrase "kill a bear". In 1923, the company adopted the name Ka-Bar from the "bear story" as its trademark. From 1923, the KA-BAR trademark was used as a ricasso stamp by Union Cutlery Co. on its line of automatic switchblade pocket knives, including the KA-BAR Grizzly, KA-BAR Baby Grizzly, and KA-BAR Model 6110 Lever Release knives.
World War IIEdit
After the United States' entry into World War II, complaints arose from Army soldiers and Marines issued World War I-era bronze or alloy-handled trench knives such as the U.S. Mark I trench knife for use in hand-to-hand fighting. The Mark I was relatively expensive and time-consuming to manufacture, and reports from the field indicated that the knife's large 'brass-knuckle' fingerguard handle made it difficult to secure in conventional scabbards while limiting the range of useful fighting grip positions. Another criticism was that the Mark I's relatively thin blade was prone to breakage when used for common utility tasks such as cutting wire or opening ammunition crates and ration cans. A final impetus came from the War Department, which had determined the need for a new multipurpose knife capable of fulfilling the roles of both a fighting and a utility knife, while at the same time conserving strategic metal resources.
The Marine Corps authorized limited issuance of a fighting knife with a stiletto blade design, the Marine Raider Stiletto designed by Lt. Col. Clifford H. Shuey, a Marine Corps engineering officer. Shuey's pattern was essentially a copy of the Fairbairn–Sykes fighting knife with altered material specifications designed to reduce dependence on critical strategic metals. The Raider stiletto was initially issued to elite Marine forces, including the entire 1st Marine Raider Battalion commanded by Colonel Merritt A. Edson, the USMC 1st Parachute Battalion, and to Marines of the 2nd Marine Raider Battalion commanded by Lt. Col. Evans F. Carlson. Primarily intended as a thrusting (stabbing) weapon, the Marines of the 1st Raider battalion found the Raider stiletto to be well designed for silent killing, but was of little use for any other purpose, and too frail for general utility tasks. After their first combat, many Marines in the 2nd Raider Battalion exchanged their Raider stilettos for No. 17 and No. 18 Collins general-purpose short machetes (machetes pequeños) purchased with unit funds. The Collins machetes, which superficially resembled a large Bowie knife, were also issued to some Army air crews as part of the Jungle Emergency Sustenance Kit of 1939.
In the absence of suitable official-issue knives, a number of Marines deploying for combat in 1942 obtained their personal knives through private purchase, usually hunting/utility patterns such as Western States Cutlery Co.'s pre-war L76 and L77 pattern knives, both of which had 7-inch (180 mm) Bowie type clip blades and leather handles. The Western States L77 was stocked at the San Diego Base Exchange at the onset of the war, and knives of this pattern were carried by many Marines in the 1st Marine Division as well as by Marine Raiders in the 2nd Marine Raider Battalion commanded by Lt. Col. Evans F. Carlson.
In response to a specification requesting a modern individual fighting knife design for the U.S. Marines, ordnance and quartermaster officials requested submissions from several military knife and tool suppliers to develop a suitable fighting and utility knife for individual Marines, using the U.S. Navy Mark 1 utility knife and existing civilian hunting/utility knives such as Western's L77 as a basis for further improvements. Working with Union Cutlery, USMC Colonel John M. Davis and Major Howard E. America contributed several important changes, including a longer, stronger blade, the introduction of a small fuller to lighten the blade, a peened pommel (later replaced by a pinned pommel), a straight (later, slightly curved) steel crossguard, and a stacked leather handle for better grip. The blade, guard, and pommel were coated with a non-reflective matte phosphate finish instead of the brightly polished steel of the original prototype. The design was given the designation of "1219C2" (although commonly known as the Ka-Bar). Notably, the Ka-Bar used a thicker blade stock than that of the USN Mark 1 utility knife, and featured a stout clip point. After extensive trials, the Ka-Bar prototype was recommended for adoption. The Marines' Quartermaster at the time initially refused to order the knives, but his decision was overruled by the Commandant. The Marine Corps adopted the Ka-Bar on November 23, 1942.
The Ka-Bar proved easy to manufacture; the first production run was shipped by Camillus Cutlery Company on January 27, 1943. After the U.S. Navy became disenchanted with blade failures on the USN Mark 1 utility knife, the latter service adopted the Ka-Bar as the US Navy Utility Knife, Mark 2. The Marine Corps in turn re-designated the Ka-Bar as either the USMC Mark 2 Combat Knife, or simply the Knife, Fighting Utility. In naval service, the knife was used as a diving and utility knife from late 1943 onward, though the stacked leather handle tended to rot and disintegrate rapidly in saltwater.
The Marine Corps issued Ka-Bar fighting utility knife throughout Marine forces, with early deliveries going primarily to elite formations. In late 1943 the Ka-Bar replaced the Marine Raider Stiletto in service, a change welcomed by the Marines of Col. Edson's 1st Raider Battalion, who found the Raider stiletto ideal for silent killing but of little use for anything else. As the knife went into large-scale production, the Marines issued the Ka-Bar Fighting Utility knife to reconnaissance and engineering units and to any Marine armed with the M1911 pistol, M1 carbine, BAR, or crew-served machine gun (rifle-armed Marines were typically issued a bayonet). Marines were often issued knives with "U.S.N. Mark 2" markings when Navy-issued Ka-Bar knives were all that was available. By 1944 the Ka-Bar knife was issued to virtually any Marine in the combat branches who desired one, and was in use by Marine Corps close combat instructors for training new recruits. Unlike the prior Marine Raider stiletto, Marines were taught to use their new knife primarily as a slashing weapon in the initial phases of hand-to-hand combat.
As its new name implied, the "Knife, Fighting Utility" was designed from the outset as a dual-purpose knife: it was both an effective combat knife and a utility tool, well-suited to the type of jungle warfare encountered by Marines in the Pacific theater. This dual-purpose design resulted in some initial criticism of the pattern as being less than ideal for knife fighting, but combat experience of returning veterans as well as reports from the battlefield dispelled doubts about its combat effectiveness.
After the Second World War, the U.S. Navy and Marine Corps continued to use the Ka-Bar Fighting Utility knife. In addition to military contract knives, the knife was produced for the civilian market, and the pattern enjoyed some popularity as a general-purpose hunting and utility knife.
Manufacturers and the "Ka-Bar" nameEdit
Camillus Cutlery Co., the first manufacturer to supply the Ka-Bar Combat Knife under contract, also produced the largest number of such knives, producing over one million examples marked "Camillus.N.Y." on the knife's crossguard before the war ended. Besides Camillus, the Union Cutlery Co., Robeson (ShurEdge) Cutlery Co., and the PAL Cutlery Co. all produced the Ka-Bar knife under military contract during World War II.
The Union Cutlery Company, the first company to manufacture a knife trademarked KA-BAR, was founded in 1897 as the Tidioute Cutlery Co. The Tidioute Cutlery Co. was dissolved and its assets taken over by Wallace R. Brown, who renamed the company Union Razor Co. which shortly thereafter became the Union Cutlery Company in 1909, headquartered in Olean, New York.
After the end of World War II, Utica Cutlery Co., Conetta Cutlery Co., Camillus Cutlery Co., and (beginning around 1980) the Ontario Knife Co. all produced the Ka-Bar under contract for the U.S. military. From approximately 1945-1952, Weske Cutlery Co. of Sandusky, Ohio purchased leftover and overrun parts from wartime Ka-Bar knife contractors and assembled them into knives for commercial sale, polishing out the original manufacturer and military markings, and fitting them with ungrooved leather handles. Though W.R. Case made two prototype Ka-Bar knives as part of a contract submission in 1942-43, no contract was ever awarded to Case for the production of military Ka-Bar Combat/Fighting Utility knives, either during or after World War II. In 1992, Case would release a modern commemorative of these prototypes, the Case XX USMC Fighting Utility Knife. The Case XX USMC Fighting Utility knife is actually manufactured for Case by Ontario Knife Co.
"KA-BAR" was a trademark of one of the four wartime manufacturers, Union Cutlery Co. and had been used on several of their previous knives since 1923. They stamped this trademark on the ricasso of all the Mark 2 knives they produced - and were second only to Camillus in terms of production, producing about one million knives during the wartime contract. Marines as early as 1944 began universally referring to their new combat knife as the "KA-BAR", regardless of manufacturer. The popular designation of the knife may also have resulted from contact with Marine Corps close combat instructors in San Diego, who appear to have used the term Ka-Bar when training recruits in the skill of knife fighting.
From 1923 until 1952, KA-BAR remained a legal trademark of Union Cutlery Company. However, in 1952 Union Cutlery renamed itself Ka-Bar Cutlery Inc. in order to capitalize on widespread public recognition of the name and trademark, which had by then become synonymous with the Mark 2 Combat Knife. While the company name changed, Ka-Bar, Inc.'s headquarters are still located in Olean, New York. In 1996, Cutco Corporation, manufacturer of Cutco Cutlery, acquired the company.
Ka-Bar makes Army and Navy versions along with USMC versions. They are the same as the Marine version except for different initials at the bottom of the blade and different symbols on the sheath. Marines today often treat the blades, guards and pommels with non-reflective black spray paint to reduce reflected light and give them additional protection against saltwater corrosion. According to Ka-Bar, its 1095 Cro-Van, a moderate carbon and low chromium steel alloy, allows the blade to hold an edge very well. The "1095 Cro-Van" steel used in the blades of contemporary Ka-Bars has a hardness of 56–58 HRC, while the guard and pommel are made from sintered 1095 carbon steel. Besides use as a fighting knife, the Ka-Bar has proved useful as a utility knife, for opening cans, digging trenches, and cutting wood, roots, wire, and cable. In 1995, the design was updated with a stainless steel blade, synthetic handle, and synthetic sheath marketed as "The Next Generation". As of June 2012 the "Next Generation" models have been discontinued. In 1999, Ka-Bar released the "D2 Extreme" version of their fighting knife, coming with the same synthetic handle and sheath that was produced with the "Next Generation", but also a blade made from D2 tool steel for extra edge retention and slightly better corrosion resistance than 1095. As of the end of 2017, the "D2 Extreme" is still in production.
Ek Commando Knife Co.Edit
In May 2014, the Ek Commando Knife Co. was purchased by Ka-Bar who began selling their version of Ek Knives in 2015.
Becker Knife and ToolEdit
In 2008, Ka-Bar began producing Ethan Becker's knife designs after his partnership with the Camillus Cutlery Company came to an end due to Camillus's bankruptcy.
- Walker, Greg (2001). KA-BAR: The Next Generation of the Ultimate Fighting Knife. Boulder, Colorado: Paladin Press. pp. 13–20, 77. ISBN 1-58160-120-4.
- Shackleford, Steve (ed.), Blade's Guide To Knives And Their Values (7th ed.), Iola, WI: Krause Publications, ISBN 1-4402-0387-3, ISBN 978-1-4402-0387-9 (2009), p. 387
- Petzal, David E., The 20 Best Knives Ever Made: The Jar-Head Favorite, Ka-Bar Marine Corps Fighting Knife, Field & Stream Magazine, Vol. CXIII, No. 2 (June 2008), p. 73: The USMC 1219C2 was first manufactured in January 1943 by the Camillus Cutlery Company of Camillus, New York
- Shackleford, Steve (ed.), Blade's Guide To Knives And Their Values (7th ed.), Iola, WI: Krause Publications, ISBN 978-1-4402-0387-9, p. 143
- How KA-BAR Got Its Name
- Freeth, Nick (2005). Made in America: from Levis to Barbie to Google. St. Paul, MN: MBI Publishing Company. p. 32. ISBN 978-0-7603-2270-3.
- Rottman, Gordon L. (2006). US Marine Rifleman 1939-45: Pacific Theater. London: Osprey Publishing. p. 32. ISBN 978-1-84176-972-1.
- Rottman, Gordon L. (2007). FUBAR: soldier slang of World War II. London: Osprey Publishing. p. 67. ISBN 978-1-84603-175-5.
- Rottman, Gordon L.; Derrick Wright (2008). Hell in the Pacific: The Battle for Iwo Jima. London: Osprey Publishing. p. 46. ISBN 978-1-84603-335-3.
- The legend of KA-BAR, Field & Stream Magazine, Vol. 83, No. 6 (October 1978), p.154
- Erickson, Mark, Antique American Switchblades, Chapter 22: KA-BAR, a trademark of Union Cutlery Co., Olean, NY, Krause Publications, ISBN 0-87349-753-8 (2004)
- KNIFE – U.S. KNIFE MODEL 1918 MKI TRENCH Springfield Armory Museum – Collection Record
- Canfield, Bruce N., U.S. INFANTRY WEAPONS OF WORLD WAR II, Lincoln, RI: Andrew Mowbray Publishers, ISBN 0-917218-67-1, ISBN 978-0-917218-67-5 (1994)
- Shackleford, Steve, ed. (2009), Blade's Guide To Knives And Their Values, Krause Publications, ISBN 978-1-4402-0387-9, p. 387: In addition to use by elite Army units such as the Rangers and U.S. airborne forces, some Marines serving in Marine Raider battalions during 1942 and 1943 carried U.S. Mark I trench knives.
- Walker (2001), p. 77
- Cassidy, William L., The Complete Book Of Knife Fighting, ISBN 0-87364-029-2, ISBN 978-0-87364-029-9 (1997), p. 47
- Blending Metals to Arm Our Fighting Men, Popular Science, Vol. 142 No. 6 (June 1943), p. 104: Demands for a modern fighting knife eventually resulted in the U.S. Army's adoption of the M3 trench knife in 1943.
- Alexander, Joseph H., Edson's Raiders: The 1st Marine Raider Battalion in World War II, Annapolis MD: Naval Institute Press, ISBN 1-55750-020-7 (2001), p. 67
- Rila, Carter, Military Myths and Misconceptions #3: The Little Machetes, Carter's Cutlery Commentarires (2005), retrieved 23 July 2011
- Rila, Carter: The Collins short machetes were commonly referred to by the 2nd Raiders as "Gung Ho Knives".
- Sledge, E.B. (2007). With the Old Breed: At Peleliu and Okinawa. New York: Random House. pp. 21–25. ISBN 978-0-89141-919-8.
- Trzaska, Frank, The USN Mark 2, Knife World, (August 2006): The original specifications designated the knife as the "Fighting Knife Mark 2".
- Sledge, E.B., With The Old Breed: At Peleleiu and Okinawa, Presidio Press, ISBN 978-0-89141-919-8 (2007),pp. 21-22: "We were introduced to the Marine's foxhole companion, the KA-BAR knife."
- MCRP 3-02B: Close Combat, Washington, D.C.: Department Of The Navy, Headquarters United States Marine Corps, 12 February 1999: "Marines use slashing techniques to close with an enemy. Slashing techniques distract or damage an opponent so Marines can close in."
- American Rifleman, C.B. Lister (ed.), Vol. 92, No. 1 (January 1944), p. 26: "Not an ideal fighting knife, it is nevertheless a highly effective weapon in jungle fighting, and, too, a sturdy tool in time of need for digging a fox hole or for opening a can of "D"ration (sic)."
- Kertzman, Joe (2007). Sporting Knives: Folders, Fixed Blades, Pocket, Military, Gent's Knives, Multi-Tools, Swords. Iola, WI: Krause Publications. p. 69. ISBN 978-0-87349-430-4.
- Shackleford, Steve (ed.), Blade's Guide To Knives And Their Values (7th ed.), Iola, WI: Krause Publications, ISBN 978-1-4402-0387-9, p. 387: Cattaraugus, Case, Western, Kinfolks, and others made huge numbers of 6-inch (150 mm) 225Q Quartermaster utility knives for the USN Quartermaster Department for opening and closing wooden crates; these knives are sometimes erroneously identified as Mark 2 Combat or Fighting Utility knives.
- Trzaska, Frank, "Rumors and Urban Legends", Knife World (March 2002)
- Green, Michael, and Stewart, Greg, Weapons of the Modern Marines, Zenith Imprint Press, ISBN 0-7603-1697-X, 9780760316979 (2004), p. 19
- "KA-BAR History – A Timeline". KA-BAR Knives Inc.
- "Glossary". kabar.com. Retrieved 5 July 2016.
1095 Cro-Van Steel - Easy to sharpen, plain carbon steel used in knife making. Proven to be one of the most popular steels used in KA-BAR knives.
- "Full-size USMC KA-BAR, Straight Edge". kabar.com. Retrieved 5 July 2016.
- "Sharon Steel 1095 Cro-Van Knife Steel". zknives.com. Retrieved 5 July 2016.
1095 Cro-Van (Sharon Steel) - Based on 1095 steel, with the addition of small amounts of V, Mo, Ni, Cr. Improved wear resistance and toughness compared to 1095. Ka-Bar ... use[s] this steel in their knives. Ka-Bar under 1095 Cro-Van name...