CoaXPress (CXP) is a digital interface standard developed for high speed image data transmission in machine vision applications. The name is a portmanteau of 'express' (as in express train) and 'coaxial' to emphasize CoaXPress is faster than other standards (e.g. Camera Link, or GigE Vision) and uses 75 ohm coaxial cables as the physical transmission medium. CoaXPress is mostly used in digital imaging applications but it is also suitable for high-speed transmission of universal digital data.
A 'device' that generates and transmits data (e.g. an industrial digital camera) is connected with one or more coaxial cables to a 'host' that receives the data (e.g. a frame grabber board in a computer). The CoaXPress standard 1.0 supports bit rates up to 6.25 Gbit/s per coaxial cable from the 'device' to the 'host'. The number of cables is not limited by the standard. Some recent CoaXPress cameras and frame grabbers use four coaxial cables providing a maximum image data rate of about 2.4 GB/s. The older Camera Link standard can only carry up to 850 MB/s. A low speed uplink, operating at 20.833 Mbit/s is available to control the 'device' or for triggering. A CoaXPress 'host' can supply 24 V over the coaxial cable up to 13 W per cable. The CoaXPress standard requires that both the 'device' and the 'host' support GenICam, a standardized generic programming interface. Other than Camera Link that is built upon pure LVDS wit no transport layer, CoaXPress transmits data in packets (cf. network packet) using 8b/10b encoding and provides CRC. CoaXPress competes with the Camera Link HS standard by the Automated Imaging Association.
CoaXPress has been developed by 6 companies, of whom Adimec, EqcoLogic and Active Silicon where among the biggest drivers, in 2008. The goal was after the failure of Visilink to develop a successor for the Camera link standard for high-speed and data-rich vision related communication. The standard was first demonstrated in November 2008 at the "Vision" trade show. After a good reception the standard writing consortium of industrial companies consisting of Adimec, Eqcologic, Active Silicon, AVAL DATA, NED and Components Express was formed early 2009. During the next Vision in 2009 the consortium was awarded the VisionAward for their efforts to further the cause of (machine)vision applications. By this time the JIIA have adopted CoaXPress to mature it to an official standard after which the first draft version 1.0 was presented in December 2010.
Cabling and connectorsEdit
The transmission medium for CoaXPress is coaxial cable with a characteristic impedance of 75 Ω. The maximum transmission distance is depending on the bit rate and the quality of the cable. RG11, RG6, RG59 and other cable types can be used. It is also possible to reuse existing coaxial cable when upgrading from an analogue to a digital camera system.
The standard connector for CoaXPress is a 75 Ω BNC connector. A second connector option is the DIN 1.0/2.3 connector. Solutions with a 5W5 connector have also been demonstrated, but this is not officially supported by the CoaXPress consortium.
CoaXPress is a scalable standard and can be used for connections from 1.25 Gbit/s up to 25 Gbit/s and more.
|Name||Bit Rate||Maximum communication distance|
|CXP-1||1.25 Gbit/s||up to 212 m|
|CXP-2||2.5 Gbit/s||up to 185 m|
|CXP-3||3.125 Gbit/s||up to 169 m|
|CXP-5||5 Gbit/s||up to 102 m|
|CXP-6||6.25 Gbit/s||up to 68 m|
|4x CXP-6||25 Gbit/s||Over 4 coaxial cables, up to 68 m|
CoaXPress supports a low speed uplink channel from frame grabber to camera. This uplink channel has a fixed bit rate of 20.833 Mbit/s. The uplink channel uses 8b/10b encoding. The uplink can be used for camera control, triggering and firmware updates.
When using the multilane DIN 1.0/2.3 cabling solution an optional high speed uplink can also be used, allowing 6.25 Gbit/s uplink communication to the camera. This can be used for very accurate triggering.
The most common application is to interface cameras to computers (via a frame grabber) on applications (such as Machine vision) which involve automated acquisition and analysis of images. Some cameras and frame grabbers have been introduced which support and utilize the CoaXPress interface standard.
So far, there is just one company, EqcoLogic, which develops CoaXPress compatible driver and equalizer devices. These devices must be used with FPGA devices, in order to implement CoaXPress standard protocol. Such standard implementation is executed using FPGA IP core, specially designed for this protocol, while it takes care of all the features defined by standard. Each side of the vision system, e.g. Camera or frame grabber, requires dedicated FPGA IP core.
- "Archived copy". Archived from the original on 2015-05-29. Retrieved 2012-12-20.CS1 maint: Archived copy as title (link) CoaXPress wins the Vision Award 2009 Retrieved December 20, 2012
- CoaXPress newsletter January 2011
- "Archived copy". Archived from the original on 2015-05-29. Retrieved 2012-12-01.CS1 maint: Archived copy as title (link) CoaXPress standard gains approval Retrieved December 1, 2012
- http://www.vision-systems.com/articles/print/volume-17/issue-2/features/coaxpress-interface-moves-into-the-mainstream.html CoaXPress interface moves into mainstream Vision Systems Feb 2010
- http://www.componentsexpress.com/PDF/CoaXPress_cables.pdf CoaXPress cabling solutions
- CoaXPress driver/equalizer chipset Archived 2013-01-22 at Archive.today
- http://www.vision-systems.com/articles/2011/05/coaxpress-standard-camera-frame-grabber-support.html 'CoaXPress standard gets camera, frame grabber support May 31, 2011 by Andrew Wilson Vision Systems Design magazine Retrieved November 28, 2012
- http://www.vision-systems.com/articles/2012/11/cameras-certified-as-compliant-with-coaxpress-standard.html Cameras certified as compliant with CoaXPress standard by Dave Wilson, Senior Editor Vision Systems Design magazine November 12, 2012 Retrieved December 1, 2012
- http://www.vision-systems.com/articles/print/volume-16/issue-12/features/looking-to-the-future-of-vision.html Product Focus - Looking to the Future of Vision by Andrew Wilson Editor Vision Systems Design magazine December 1, 2011 Retrieved December 1, 2012
- http://www.designnews.com/document.asp?doc_id=235998 CoaXPress Interface Moves to Machine Vision Mainstream by AAnn R. Thryft November 28, 2011 Retrieved December 1, 2012
- Official website
- CoaXPress standard 1.0 Japan Industrial Imaging Association Standard
- CoaXPress standard 1.1 Japan Industrial Imaging Association Standard
- CoaXPress standard 1.1.1 Japan Industrial Imaging Association Standard