An anti-aliasing filter (AAF) is a filter used before a signal sampler to restrict the bandwidth of a signal to satisfy the Nyquist–Shannon sampling theorem over the band of interest. Since the theorem states that unambiguous reconstruction of the signal from its samples is possible when the power of frequencies above the Nyquist frequency is zero, a brick wall filter is an idealized but impractical AAF. A practical AAF trades off between bandwidth and aliasing. A practical anti-aliasing filter will typically permit some aliasing to occur or attenuate or otherwise distort some in-band frequencies close to the Nyquist limit. For this reason, many practical systems sample higher than would be theoretically required by a perfect AAF in order to ensure that all frequencies of interest can be reconstructed, a practice called oversampling.
In the case of optical image sampling, as by image sensors in digital cameras, the anti-aliasing filter is also known as an optical low-pass filter (OLPF), blur filter, or AA filter. The mathematics of sampling in two spatial dimensions is similar to the mathematics of time-domain sampling, but the filter implementation technologies are different. The typical implementation in digital cameras is two layers of birefringent material such as lithium niobate, which spreads each optical point into a cluster of four points.
The choice of spot separation for such a filter involves a tradeoff among sharpness, aliasing, and fill factor (the ratio of the active refracting area of a microlens array to the total contiguous area occupied by the array). In a monochrome or three-CCD or Foveon X3 camera, the microlens array alone, if near 100% effective, can provide a significant anti-aliasing effect, while in color filter array (CFA, e.g. Bayer filter) cameras, an additional filter is generally needed to reduce aliasing to an acceptable level.
The Pentax K-3 from Ricoh introduced a unique sensor-based anti-aliasing filter. The filter works by micro vibrating the sensor element. The user can turn the vibration on or off, selecting anti-aliasing or no anti-aliasing.
Anti-aliasing filters are commonly used at the input of digital signal processing system's analog-to-digital converter; similar filters are used as reconstruction filters at the output of such systems, for example in music players. In the latter case, the filter prevents imaging, the reverse process of aliasing where in-band frequencies are mirrored out of band.
A technique known as oversampling is commonly used in audio ADCs. The idea is to use a higher intermediate digital sample rate, so that a nearly ideal digital filter can sharply cut off aliasing near the original low Nyquist frequency and give better phase response, while a much simpler analog filter can stop frequencies above the new higher Nyquist frequency. Because analog filters have relatively high cost and limited performance, relaxing the demands on the analog filter can greatly reduce both aliasing and cost. Furthermore, because some noise is averaged out, the higher sampling rate can moderately improve SNR.
Alternatively, a signal may be intentionally oversampled without an intermediate frequency to reduce the requirements on the anti-alias filter. For example, CD audio typically extends up to 20 kHz, but is sampled with a 22.05 kHz Nyquist rate. By oversampling by 2.05 kHz, both aliasing and attenuation of higher audio frequencies can be prevented even with less than ideal filters.
Often, an anti-aliasing filter is a low-pass filter; this is not a requirement, however. Generalizations of the Nyquist–Shannon sampling theorem allow sampling of other band-limited passband signals instead of baseband signals.
For signals that are bandwidth limited, but not centered at zero, a band-pass filter can be used as an anti-aliasing filter. For example, this could be done with a single-sideband modulated or frequency modulated signal. If one desired to sample an FM radio broadcast centered at 87.9 MHz and bandlimited to a 200 kHz band, then an appropriate anti-alias filter would be centered on 87.9 MHz with 200 kHz bandwidth (or pass-band of 87.8 MHz to 88.0 MHz), and the sampling rate would be no less than 400 kHz, but should also satisfy other constraints to prevent aliasing.
It is very important to avoid input signal overload when using an anti-aliasing filter. If the signal is strong enough, it can cause clipping at the analog-to-digital converter, even after filtering. When distortion due to clipping occurs after the anti-aliasing filter, it can create components outside the passband of the anti-aliasing filter; these components can then alias, causing the reproduction of other non-harmonically related frequencies.
- Adrian Davies and Phil Fennessy (2001). Digital imaging for photographers (Fourth ed.). Focal Press. ISBN 0-240-51590-0.
- S. B. Campana and D. F. Barbe (1974). "Tradeoffs between aliasing and MTF". Proceedings of the Electro-Optical Systems Design Conference – 1974 West International Laser Exposition – San Francisco, Calif., November 5-7, 1974. Chicago: Industrial and Scientific Conference Management, Inc. pp. 1–9. Bibcode:1974eosd.conf....1C.
- Brian W. Keelan (2004). Handbook of Image Quality: Characterization and Prediction. Marcel–Dekker. ISBN 0-8247-0770-2.
- Sidney F. Ray (1999). Scientific photography and applied imaging. Focal Press. p. 61. ISBN 978-0-240-51323-2.
- Michael Goesele (2004). New Acquisition Techniques for Real Objects and Light Sources in Computer Graphics. Books on Demand. p. 34. ISBN 978-3-8334-1489-3.
- "Pentax K-3". Retrieved November 29, 2013.