Miller twist rule

Miller twist rule is a mathematical formula derived by Don Miller to determine the rate of twist to apply to a given bullet to provide optimum stability using a rifled barrel.^[1] Miller suggests that, while Greenhill's formula works well, there are better and more precise methods for determining the proper twist rate that are no more difficult to compute.

Formula edit

A diagram of a .30-06 Springfield showing the bullet diameter (7.85 mm) and length (31.28 mm).

The following formula is one recommended by Miller:^[1]

${t}^{2}={\frac {30m}{sd^{3}l(1+l^{2})}}$

where

m = bullet mass in grains (defined as 64.79891 milligrams)
s = gyroscopic stability factor (dimensionless)
d = bullet diameter in inches
l = bullet length in calibers (that is, length in relation to the diameter)
t = twist rate in calibers per turn

Also, since one "caliber" in this context is one bullet diameter, we have:

${t}={\frac {T}{d}}$

where $T$ = twist rate in inches per turn, and

${l}={\frac {L}{d}}$

where $L$ = bullet length in inches.

Stability factor edit

Solving Miller's formula for $s$ gives the stability factor for a known bullet and twist rate:

${s}={\frac {30m}{t^{2}d^{3}l(1+l^{2})}}$

Twist in inches per turn edit

Solving the formula for $T$ gives the twist rate in inches per turn:

${T}={\sqrt {\frac {30m}{sdl(1+l^{2})}}}$

Notes edit

Note that the constant 30 in the formula is Miller's rough approximation of velocity (2800 ft/sec or 853 m/s), standard temperature (59 degrees Fahrenheit or 15 celsius) and pressure (750 mmHg or 1000 hPa, and 78% relative humidity). Miller states that these values are taken from the Army Standard Metro but does note that his values are slightly off. He goes on to point out that the difference should be small enough that it can be ignored.

It should also be noted that the bullet density is missing from Miller's formula despite the fact that Miller himself states his formula expands upon Greenhill's. The bullet density in the equation above is implicit in $m$ through the moment of inertia approximation.

Finally, note that the denominator of Miller's formula is based upon the relative shape of a modern bullet. The term $l(1+l^{2})$ roughly indicates a shape similar to that of an American football.

Safe values edit

When computing using this formula, Miller suggests several safe values that can be used for some of the more difficult to determine variables. For example, he states that a mach number of $M$ = 2.5 (roughly 2800 ft/sec, assuming standard conditions at sea level where 1 Mach is roughly 1116 ft/sec) is a safe value to use for velocity. He also states that rough estimates involving temperature should use $s$ = 2.0.

Example edit

Using a Nosler Spitzer bullet in a .30-06 Springfield, which is similar to the one pictured above, and substituting values for the variables, we determine the estimated optimum twist rate.^[2]

$t={\sqrt {\frac {30m}{sd^{3}l(1+l^{2})}}}$

where

m = 180 grains
s = 2.0 (the safe value noted above)
d = .308 inches
l = 1.180" /.308" = 3.83 calibers

$t={\sqrt {\frac {30*180}{2.0*.308^{3}*3.83(1+3.83^{2})}}}=39.2511937$

The result indicates an optimum twist rate of 39.2511937 calibers per turn. Determining $T$ from $t$ we have

$T=39.2511937*.308=12.0893677$

Thus the optimum rate of twist for this bullet should be approximately 12 inches per turn. The typical twist of .30-06 caliber rifle barrels is 10 inches per turn, accommodating heavier bullets than in this example. A different twist rate often helps explain why some bullets work better in certain rifles when fired under similar conditions.

Comparison to Greenhill's formula edit

Greenhill's formula is much more complicated in full form. The rule of thumb that Greenhill devised based upon his formula is actually what is seen in most writing, including Wikipedia. The rule of thumb is:

$Twist={\frac {CD^{2}}{L}}\times {\sqrt {\frac {SG}{10.9}}}$

The actual formula is:^[3]

$S={\frac {s^{2}*m^{2}}{C_{M_{\alpha }}\div \sin(a)*t*d*v^{2}}}$

where

S = gyroscopic stability
s = twist rate in radians per second
m = polar moment of inertia
$C_{M_{\alpha }}$ = pitching moment coefficient
a = angle of attack
t = transverse moment of inertia
d = air density
v = velocity

Thus, Miller essentially took Greenhill's rule of thumb and expanded it slightly, while keeping the formula simple enough to be used by someone with basic math skills. To improve on Greenhill, Miller used mostly empirical data and basic geometry.

Corrective equations edit

Miller notes several corrective equations that can be used:

The velocity ( $v$ ) correction for twist ( $T$ ): $f_{v}{^{1/2}}=[{\frac {v}{2800}}]^{1/6}$

The velocity ( $v$ ) correction for stability factor ( $s$ ): $f_{v}=[{\frac {v}{2800}}]^{1/3}$

The altitude ( $a$ ) correction under standard conditions: $f_{a}=e^{3.158x10^{-5}*h}$ where $h$ is altitude in feet.

References edit

^ ^a ^b Miller, Don. How Good Are Simple Rules For Estimating Rifling Twist^{[permanent dead link]}, Precision Shooting - June 2009
^ Nosler - Up Front Archived 2012-01-14 at the Wayback Machine, Accessed February 2012
^ Mosdell, Matthew. The Greenhill Formula. "Archived copy". Archived from the original on 2011-07-18. Retrieved 2009-08-19.{{cite web}}: CS1 maint: archived copy as title (link) (Accessed 2009 AUG 19)

External links edit

Calculators for stability and twist edit

[c1-1] Miller, Don. How Good Are Simple Rules For Estimating Rifling Twist^{[permanent dead link]}, Precision Shooting - June 2009

[2] Nosler - Up Front Archived 2012-01-14 at the Wayback Machine, Accessed February 2012

[3] Mosdell, Matthew. The Greenhill Formula. "Archived copy". Archived from the original on 2011-07-18. Retrieved 2009-08-19.{{cite web}}: CS1 maint: archived copy as title (link) (Accessed 2009 AUG 19)

[1]

[2]

[3]

Miller twist rule

Contents

Formula edit

Stability factor edit

Twist in inches per turn edit

Notes edit

Safe values edit

Example edit

Comparison to Greenhill's formula edit

Corrective equations edit

See also edit

References edit

External links edit

Calculators for stability and twist edit