Open main menu

Wikipedia β

Electronic delay storage automatic calculator

  (Redirected from Electronic Delay Storage Automatic Calculator)
EDSAC

The electronic delay storage automatic calculator (EDSAC) was an early British computer.[1] Inspired by John von Neumann's seminal First Draft of a Report on the EDVAC, the machine was constructed by Maurice Wilkes and his team at the University of Cambridge Mathematical Laboratory in England. EDSAC was the second electronic digital stored-program computer to go into regular service.[2]

Later the project was supported by J. Lyons & Co. Ltd., a British firm, who were rewarded with the first commercially applied computer, LEO I, based on the EDSAC design. Work on EDSAC started during 1947,[3] and it ran its first programs on 6 May 1949, when it calculated a table of squares[4] and a list of prime numbers. EDSAC 1 was finally shut down on 11 July 1958, having been superseded by EDSAC 2, which remained in use until 1965.[5]

Contents

Technical overviewEdit

Physical componentsEdit

As soon as EDSAC was operational, it began serving the University's research needs. It used mercury delay lines for memory, and derated vacuum tubes for logic. Cycle time was 1.5 ms for all ordinary instructions, 6 ms for multiplication. Input was via five-hole punched tape and output was via a teleprinter.

Initially registers were limited to an accumulator and a multiplier register. In 1953, David Wheeler, returning from a stay at the University of Illinois, designed an index register as an extension to the original EDSAC hardware.

A magnetic tape drive was added in 1952 but never worked sufficiently well to be of real use.[6]

Until 1952, the available main memory (instructions and data) was only 512 18-bit words, and there was no backing store.[7] The delay lines (or "tanks") were arranged in two batteries providing 512 words each. The second battery came into operation in 1952.[6]

The full 1024-word delay line store was not available until 1955 or early 1956,[8] limiting programs to about 800 words until then.

John Lindley (diploma student 1958–1959) mentioned "the incredible difficulty we had ever to produce a single correct piece of paper tape with the crude and unreliable home-made punching, printing and verifying gear available in the late 50s".[9]

Memory and instructionsEdit

 
Maurice Wilkes and Bill Renwick in front of the complete EDSAC

The EDSAC's main memory consisted of 1024 locations, though only 512 locations were initially installed. Each contained 18 bits, but the topmost bit was always unavailable due to timing problems, so only 17 bits were used. An instruction consisted of a five-bit instruction code, one spare bit, a ten bit operand (usually a memory address), and a length bit to control whether the instruction used a 17-bit or a 35-bit operand (two consecutive words, little-endian). All instruction codes were by design represented by one mnemonic letter, so that the Add instruction, for example, used the EDSAC character code for the letter A.

Internally, the EDSAC used two's complement, binary numbers. Numbers were either 17 bits (one word) or 35 bits (two words) long. Unusually, the multiplier was designed to treat numbers as fixed-point fractions in the range −1 ≤ x < 1, i.e. the binary point was immediately to the right of the sign. The accumulator could hold 71 bits, including the sign, allowing two long (35-bit) numbers to be multiplied without losing any precision.

The instructions available were:

  • Add
  • Subtract
  • Multiply-and-add
  • AND-and-add (called "Collate")
  • Shift Left
  • Arithmetic shift Right
  • Load multiplier register
  • Store (and optionally clear) accumulator
  • Conditional Goto
  • Read Input tape
  • Print character
  • Round accumulator
  • No-op
  • Stop.

There was no division instruction (but various division subroutines were supplied) and no way to directly load a number into the accumulator (a "sTore and zero accumulator" instruction followed by an "Add" instruction were necessary for this). There was no unconditional jump instruction, nor was there a procedure call instruction - it had not yet been invented.

System softwareEdit

The initial orders were hard-wired on a set of uniselector switches and loaded into the low words of memory at startup. By May 1949, the initial orders provided a primitive relocating assembler taking advantage of the mnemonic design described above, all in 31 words. This was the world's first assembler, and arguably the start of the global software industry. There is a simulation of EDSAC available and a full description of the initial orders and first programs.

The machine was used by other members of the University to solve real problems, and many early techniques were developed that are now included in operating systems. Users prepared their programs by punching them (in assembler) onto a paper tape. They soon became good at being able to hold the paper tape up to the light and read back the codes. When a program was ready it was hung on a length of line strung up near the paper tape reader. The machine operators, who were present during the day, selected the next tape from the line and loaded it into EDSAC. This is of course well known today as job queues. If it printed something then the tape and the printout were returned to the user, otherwise they were informed at which memory location it had stopped. Debuggers were some time away, but a CRT screen could be set to display the contents of a particular piece of memory. This was used to see if a number was converging, for example. A loudspeaker was connected to the accumulator's sign bit; experienced users knew healthy and unhealthy sounds of programs, particularly programs 'hung' in a loop. After office hours certain "Authorised Users" were allowed to run the machine for themselves, which went on late into the night until a valve blew – which usually happened according to one such user.[10]

Programming techniqueEdit

 
EDSAC monitoring desk

The early programmers had to make use of techniques frowned upon today — especially altering the code. As there was no index register until much later, the only way of accessing an array was to alter which memory location a particular instruction was referencing.

David Wheeler, who earned the world's first Computer Science PhD working on the project, is credited with inventing the concept of a subroutine. Users wrote programs that called a routine by jumping to the start of the subroutine with the return address (i.e. the location-plus-one of the jump itself) in the accumulator (a Wheeler jump). By convention the subroutine expected this and the first thing it did was to modify its concluding jump instruction to that return address. Multiple and nested subroutines could be called so long as the user knew the length of each one in order to calculate the location to jump to; recursive calls were forbidden. The user then copied the code for the subroutine from a master tape onto their own tape following the end of their own program.

Application softwareEdit

The subroutine concept led to the availability of a substantial subroutine library. By 1951, 87 subroutines in the following categories were available for general use: floating point arithmetic; arithmetic operations on complex numbers; checking; division; exponentiation; routines relating to functions; differential equations; special functions; power series; logarithms; miscellaneous; print and layout; quadrature; read (input); nth root; trigonometric functions; counting operations (simulating repeat until loops, while loops and for loops); vectors; and matrices.

Applications of EDSACEdit

The “brain” [computer] may one day come down to our level [of the common people] and help with our income-tax and book-keeping calculations. But this is speculation and there is no sign of it so far.

— British newspaper The Star in a June 1949 news article about the EDSAC computer, long before the era of the personal computers.[15]

Further developmentsEdit

EDSAC's successor, EDSAC 2, was commissioned in 1958.

In 1961, an EDSAC 2 version of Autocode, an ALGOL-like high-level programming language for scientists and engineers, was developed by David Hartley.

In the mid-1960s, a successor to the EDSAC 2 was planned, but the move was instead made to the Titan, a prototype Atlas 2 developed from the Atlas Computer of the University of Manchester, Ferranti, and Plessey.

EDSAC Replica ProjectEdit

On 13 January 2011, the Computer Conservation Society announced that it planned to build a working replica of EDSAC, at the National Museum of Computing (TNMoC) in Bletchley Park supervised by Andrew Herbert, who studied under Maurice Wilkes.[16] The first parts of the recreation were switched on in November 2014.[17] The ongoing project is open to visitors of the museum. As of November 2016, commissioning of the fully completed and operational state of the replica is estimated by the autumn of 2017.[18]

See alsoEdit

ReferencesEdit

  1. ^ Wilkes, W. V.; Renwick, W. (1950). "The EDSAC (Electronic delay storage automatic calculator)". Math. Comp. 4 (30): 61–65. doi:10.1090/s0025-5718-1950-0037589-7. 
  2. ^ The Manchester Small-Scale Experimental Machine, nicknamed "Baby", predated EDSAC as a stored-program computer, but was built as a test bed for the Williams tube and not as a machine for practical use. http://www.cl.cam.ac.uk/conference/EDSAC99/history.html. However, the Manchester Mark 1 of 1949 (not to be confused with the 1948 SSEM prototype) was available for general use by other university departments and Ferranti in April 1949 http://www.computer50.org/mark1/MM1.html despite being still under development.
  3. ^ [1] Archived 7 December 2014 at the Wayback Machine.
  4. ^ "Pioneer computer to be rebuilt". Cam. 62: 5. Lent 2011.  Check date values in: |date= (help) To be precise, EDSAC's first program printed a list of the squares of the integers from 0 to 99 inclusive.
  5. ^ EDSAC 99: 15–16 April 1999 (PDF), University of Cambridge Computer Laboratory, 6 May 1999, pp. 68, 69, retrieved 2013-06-29 
  6. ^ a b Some EDSAC statistics
  7. ^ EDSAC 1 and after
  8. ^ EDSAC 1 and after
  9. ^ EDSAC 1 and after
  10. ^ Professor David Barron, Emeritus Professor of the University of Southampton at a Cambridge Computer Lab seminar to mark the 60th anniversary 6 May 2009.
  11. ^ Gene Frequencies in a Cline Determined by Selection and Diffusion, R. A. Fisher, Biometrics, Vol. 6, No. 4 (Dec. 1950), pp. 353–361
  12. ^ Caldwell – largest known primes by year One reference gives Miller, J. C. P. "Larger Prime Numbers" (1951) Nature 168(4280):838, but the abstract does not mention it.
  13. ^ Wolf, Mark J. P. (2012-08-16). Encyclopedia of Video Games: The Culture, Technology, and Art of Gaming. Greenwood Publishing Group. pp. 3–7. ISBN 978-0-313-37936-9. 
  14. ^ Cohen, D. S. (2014-09-20). "OXO aka Noughts and Crosses - The First Video Game". About.com. IAC. Archived from the original on 2015-12-22. Retrieved 2015-12-18. 
  15. ^ [2]
  16. ^ Ward, Mark (13 January 2011). "Pioneering Edsac computer to be built at Bletchley Park". BBC News. Retrieved 2011-01-13. 
  17. ^ Museum switches on historic computer
  18. ^ Palmer, Danny (24 November 2016). "Inside the project to rebuild the EDSAC, one of the world's first general purpose computers". Retrieved 2016-12-01. 

Further readingEdit

External linksEdit