Direct and indirect band gaps
In semiconductor physics, the band gap of a semiconductor can be of two basic types, a direct band gap or an indirect band gap. The minimal-energy state in the conduction band and the maximal-energy state in the valence band are each characterized by a certain crystal momentum (k-vector) in the Brillouin zone. If the k-vectors are different, the material has an "indirect gap". The band gap is called "direct" if the crystal momentum of electrons and holes is the same in both the conduction band and the valence band; an electron can directly emit a photon. In an "indirect" gap, a photon cannot be emitted because the electron must pass through an intermediate state and transfer momentum to the crystal lattice.
Implications for radiative recombinationEdit
Interactions among electrons, holes, phonons, photons, and other particles are required to satisfy conservation of energy and crystal momentum (i.e., conservation of total k-vector). A photon with an energy near a semiconductor band gap has almost zero momentum. One important process is called radiative recombination, where an electron in the conduction band annihilates a hole in the valence band, releasing the excess energy as a photon. This is possible in a direct band gap semiconductor if the electron has a k-vector near the conduction band minimum (the hole will share the same k-vector), but not possible in an indirect band gap semiconductor, as photons cannot carry crystal momentum, and thus conservation of crystal momentum would be violated. For radiative recombination to occur in an indirect band gap material, the process must also involve the absorption or emission of a phonon, where the phonon momentum equals the difference between the electron and hole momentum. It can also, instead, involve a crystallographic defect, which performs essentially the same role. The involvement of the phonon makes this process much less likely to occur in a given span of time, which is why radiative recombination is far slower in indirect band gap materials than direct band gap ones. This is why light-emitting and laser diodes are almost always made of direct band gap materials, and not indirect band gap ones like silicon.
The fact that radiative recombination is slow in indirect band gap materials also means that, under most circumstances, radiative recombinations will be a small proportion of total recombinations, with most recombinations being non-radiative, taking place at point defects or at grain boundaries. However, if the excited electrons are prevented from reaching these recombination places, they have no choice but to eventually fall back into the valence band by radiative recombination. This can be done by creating a dislocation loop in the material.[clarification needed] At the edge of the loop, the planes above and beneath the "dislocation disk" are pulled apart, creating a negative pressure, which raises the energy of the conduction band substantially, with the result that the electrons cannot pass this edge. Provided that the area directly above the dislocation loop is defect-free (no non-radiative recombination possible), the electrons will fall back into the valence shell by radiative recombination, thus emitting light. This is the principle on which "DELEDs" (Dislocation Engineered LEDs) are based.
Implications for light absorptionEdit
The exact reverse of radiative recombination is light absorption. For the same reason as above, light with a photon energy close to the band gap can penetrate much farther before being absorbed in an indirect band gap material than a direct band gap one (at least insofar as the light absorption is due to exciting electrons across the band gap).
This fact is very important for photovoltaics (solar cells). Silicon is the most common solar-cell material, despite the fact that it is indirect-gap and therefore does not absorb light very well. Silicon solar cells are typically hundreds of microns thick; if it was much thinner, much of the light (particularly in the infrared) would simply pass through. By comparison, thin-film solar cells are made of direct band gap materials (such as CdTe, CIGS or CZTS), which absorb the light in a much thinner region, and consequently can be made with a very thin active layer (often less than 1 micron thick).
The absorption spectrum of an indirect band gap material usually depends more on temperature than that of a direct material, because at low temperatures there are fewer phonons, and therefore it is less likely that a photon and phonon can be simultaneously absorbed to create an indirect transition. For example, silicon is opaque to visible light at room temperature, but transparent to red light at liquid helium temperatures, because red photons can only be absorbed in an indirect transition.[clarification needed]
Formula for absorptionEdit
A common and simple method for determining whether a band gap is direct or indirect uses absorption spectroscopy. By plotting certain powers of the absorption coefficient against photon energy, one can normally tell both what value the band gap is, and whether or not it is direct.
- , with
- is the absorption coefficient, a function of light frequency
- is light frequency
- is Planck's constant ( is the energy of a photon with frequency )
- is reduced Planck's constant ( )
- is the band gap energy
- is a certain frequency-independent constant, with formula above
- , where and are the effective masses of the electron and hole, respectively ( is called a "reduced mass")
- is the elementary charge
- is the (real) index of refraction
- is the vacuum permittivity
- is a "matrix element", with units of length and typical value the same order of magnitude as the lattice constant.
This formula is valid only for light with photon energy larger, but not too much larger, than the band gap (more specifically, this formula assumes the bands are approximately parabolic), and ignores all other sources of absorption other than the band-to-band absorption in question, as well as the electrical attraction between the newly created electron and hole (see exciton). It is also invalid in the case that the direct transition is forbidden, or in the case that many of the valence band states are empty or conduction band states are full.
On the other hand, for an indirect band gap, the formula is:
- is the energy of the phonon that assists in the transition
- is Boltzmann's constant
- is the thermodynamic temperature
This formula involves the same approximations mentioned above.
Therefore, if a plot of versus forms a straight line, it can normally be inferred that there is a direct band gap, measurable by extrapolating the straight line to the axis. On the other hand, if a plot of versus forms a straight line, it can normally be inferred that there is an indirect band gap, measurable by extrapolating the straight line to the axis (assuming ).
In some materials with an indirect gap, the value of the gap is negative. The top of the valence band is higher than the bottom of the conduction band in energy. Such materials are known as semimetals.
- Optoelectronics, by E. Rosencher, 2002, equation (7.25).
- Pankove has the same equation, but with an apparently different prefactor . However, in the Pankove version, the units / dimensional analysis appears not to work out.
- J.I. Pankove, Optical Processes in Semiconductors. Dover, 1971.
- B. Van Zeghbroeck's Principles of Semiconductor Devices at Electrical and Computer Engineering Department of University of Colorado at Boulder