Very high temperature reactor
The very high temperature reactor (VHTR), or high temperature gas-cooled reactor (HTGR), is a Generation IV reactor concept that uses a graphite-moderated nuclear reactor with a once-through uranium fuel cycle. The VHTR is a type of high temperature reactor (HTR) that can conceptually have an outlet temperature of 1000°C. The reactor core can be either a “prismatic block” or a "pebble-bed" core. The high temperatures enable applications such as process heat or hydrogen production via the thermochemical sulfur-iodine cycle.
The VHTR is a type of high temperature reactor that conceptually can reach higher outlet temperatures (up to 1000°C); however, in practice the term "VHTR" is usually thought of as a gas-cooled reactor, and commonly used interchangeably with "HTGR" (high temperature gas-cooled reactor).
There are two main types of HTGRs: pebble bed reactors (PBR) and prismatic block reactors (PMR). The prismatic block reactor refers to a prismatic block core configuration, in which hexagonal graphite blocks are stacked to fit in a cylindrical pressure vessel. The pebble bed reactor (PBR) design consists of fuel in the form of pebbles, stacked together in a cylindrical pressure vessel, like a gum-ball machine. Both reactors may have the fuel stacked in an annulus region with a graphite center spire, depending on the design and desired reactor power.
The Russian VHTR is also a HTGR.
The HTGR design was first proposed by the staff of the Power Pile Division of the Clinton Laboratories (known now as Oak Ridge National Laboratory) in 1947. Professor Dr. Rudolf Schulten in Germany also played a role in development during the 1950s. The Peach Bottom reactor in the United States was the first HTGR to produce electricity, and did so very successfully, with operation from 1966 through 1974 as a technology demonstrator. Fort St. Vrain Generating Station was one example of this design that operated as an HTGR from 1979 to 1989; though the reactor was beset by some problems which led to its decommissioning due to economic factors, it served as proof of the HTGR concept in the United States (though no new commercial HTGRs have been developed there since).[not in citation given] HTGRs have also existed in the United Kingdom (the Dragon reactor) and Germany (AVR reactor and THTR-300), and currently exist in Japan (the HTTR using prismatic fuel with 30 MWth of capacity) and China (the HTR-10, a pebble-bed design with 10 MWe of generation). Two full-scale pebble-bed HTGRs HTR-PM, each with 100 - 195 MWe of electrical production capacity are under construction in China as of November 2009, and are promoted in several countries by reactor designers.
Nuclear reactor design
The neutron moderator is graphite, although whether the reactor core is configured in graphite prismatic blocks or in graphite pebbles depends on the HTGR design.
The fuel used in HTGRs is coated fuel particles, such as TRISO fuel particles. Coated fuel particles have fuel kernels, usually made of uranium dioxide, however, uranium carbide or uranium oxycarbide are also possibilities. Uranium oxycarbide combines uranium carbide with the uranium dioxide to reduce the oxygen stoichiometry. Less oxygen may lower the internal pressure in the TRISO particles caused by the formation of carbon monoxide, due to the oxidization of the porous carbon layer in the particle. The TRISO particles are either dispersed in a pebble for the pebble bed design or molded into compacts/rods that are then inserted into the hexagonal graphite blocks. The QUADRISO fuel concept conceived at Argonne National Laboratory has been used to better manage the excess of reactivity.
Helium has been the coolant used in most HTGRs to date, and the peak temperature and power depend on the reactor design. Helium is an inert gas, so it will generally not chemically react with any material. Additionally, exposing helium to neutron radiation does not make it radioactive, unlike most other possible coolants.
The molten salt cooled variant, the LS-VHTR, similar to the advanced high temperature reactor (AHTR) design, uses a liquid fluoride salt for cooling in a pebble core.(section 3) It shares many features with a standard VHTR design, but uses molten salt as a coolant instead of helium. The pebble fuel floats in the salt, and thus pebbles are injected into the coolant flow to be carried to the bottom of the pebble bed, and are removed from the top of the bed for recirculation. The LS-VHTR has many attractive features, including: the ability to work at high temperatures (the boiling point of most molten salts being considered are >1,400°C), low pressure operation, high power density, better electric conversion efficiency than a helium-cooled VHTR operating at similar conditions, passive safety systems, and better retention of fission products in case an accident occurred.
In the prismatic designs, control rods are inserted in holes cut in the graphite blocks that make up the core. The VHTR will be controlled like current PBMR designs if it utilizes a pebble bed core, the control rods will be inserted in the surrounding graphite reflector. Control can also be attained by adding pebbles containing neutron absorbers.
The high temperature, high neutron dose, and, if using a molten salt coolant, the corrosive environment,(p46) of the VHTR require materials that exceed the limitations of current nuclear reactors. In a study of Generation IV reactors in general (of which there are numerous designs, including the VHTR), Murty and Charit suggest that materials that have high dimensional stability, either with or without stress, maintain their tensile strength, ductility, creep resistance, etc. after aging, and are corrosion resistant are primary candidates for use in VHTRs. Some materials suggested include nickel-base superalloys, silicon carbide, specific grades of graphite, high chromium steels, and refractory alloys. Further research is being conducted at US national laboratories as to which specific issues must be addressed in the Generation IV VHTR prior to construction.
Safety features and other benefits
The design takes advantage of the inherent safety characteristics of a helium-cooled, graphite-moderated core with specific design optimizations. The graphite has large thermal inertia and the helium coolant is single phase, inert, and has no reactivity effects. The core is composed of graphite, has a high heat capacity and structural stability even at high temperatures. The fuel is coated uranium-oxycarbide which permits high burn-up (approaching 200 GWd/t) and retains fission products. The high average core-exit temperature of the VHTR (1,000°C) permits emissions-free production of process heat.
- McCullough, C. Rodgers; Staff, Power Pile Division (1947-09-15). "Summary Report on Design and Development of High Temperature Gas-Cooled Power Pile". Oak Ridge, TN, USA: Clinton Laboratories (now Oak Ridge National Laboratory). Retrieved 2009-11-23.
- IAEA HTGR Knowledge Base
- Current status and technical description of Chinese 2 x 250 MWth HTR-PM demonstration plant
- D. Olander J. Nucl. Mater. 389 (2009) 1-22.
- "High temperature gas cool reactor technology development" (PDF). IAEA. 1996-11-15. p. 61. Retrieved 2009-05-08.
- "Thermal performance and flow instabilities in a multi-channel, helium-cooled, porous metal divertor module". Inist. 2000. Retrieved 2009-05-08.
- Ingersoll, D.; Forsberg, C.; MacDonald, P. (February 2007). "Trade Studies for the Liquid-Salt-Cooled Very High-Temperature Reactor: Fiscal Year 2006 Progress Report". ORNL/TM-2006/140 (Oak Ridge National Laboratory).
- K.L. Murty, I. Charit, J. Nucl. Mater. 383 (2008) 189-195.