The Triumph Stag is a 2+2 sports tourer which was sold between 1970 and 1978 by the British Triumph Motor Company, styled by Italian designer Giovanni Michelotti.

Triumph Stag
1974 Triumph Stag (with after-market wheels)
ManufacturerTriumph Motor Company
25,939 made[1]
DesignerGiovanni Michelotti
Body and chassis
ClassSports tourer
LayoutFront-engine, rear-wheel-drive
RelatedTriumph TR250
Triumph 2000
Engine3.0L Triumph V8
Wheelbase100 in (2,540 mm)
Length173 in (4,394 mm)[2]
Width63.5 in (1,613 mm)
Height49.5 in (1,257 mm)
Kerb weight2,800 lb (1,300 kg)

Design and styling


Envisioned as a luxury sports car, the Stag was designed to compete directly with the Mercedes-Benz SL class models. All Stags were four-seater convertible coupés, but for structural rigidity – and to meet proposed American rollover standards of the time – the Stag required a B-pillar "roll bar" hoop connected to the windscreen frame by a T-bar. A body-colour removable hard top with defrost wires on the rear window, full headliner and lever operated quarter windows was a popular factory option.

The car started as a styling experiment cut and shaped from a 1963–64 pre-production 2000 saloon, also styled by Giovanni Michelotti. His agreement was, if Harry Webster, Director of Engineering at Triumph, liked the design, Triumph could use the prototype as the basis for a new model. Webster loved the design and took the prototype back to England. The result, a two-door drophead (convertible), had little in common with the styling of its progenitor 2000, but retained the suspension and drive line. Triumph liked the Michelotti design so much that they propagated the styling lines of the Stag into the new T2000/T2500 Mark II saloon and estate model lines of the 1970s.[citation needed]

Triumph gave new projects four-letter development code names (e.g. Bomb for the Spitfire) and the Stag was the only Triumph to take its development code name into production.


1972 Stag with Rostyle wheel trims, retrofitted 1976 stainless steel sill panels
1974 Stag interior

The initial Stag design used the saloon's 2.0-litre six cylinder engine which was intended to be uprated to 2.5-litres for production cars, but Webster intended the Stag, large saloons and estate cars to use a new Triumph-designed overhead cam (OHC) 2.5-litre fuel injected (PI) V8. In 1968, under the direction of Engineering Director Harry Webster and his successor as Chief Engineer, Spen King, the new 2.5 PI V8 was enlarged to 2,997 cc (3 L; 183 cu in) to increase the power available. To meet emission standards in the US, a key target market, the troublesome mechanical fuel injection was dropped in favour of dual Zenith-Stromberg 175 CDSE carburetors. In common with several other manufacturers,[3] a key aim of Triumph's engineering strategy at the time was to create a family of in-line and V engines of different size around a common crankshaft. The various configurations Triumph envisaged would enable the production of four-, six-, and eight-cylinder power plants of capacity between 1.5 and 4 litres, sharing many parts, and hence offering economies of manufacturing scale and of mechanic training. A number of iterations of Triumph's design went into production, notably a 2.0-litre slant four-cylinder engine used in the later Dolomite and TR7, and a variant manufactured by StanPart that was initially used in the Saab 99. In 1968 the Saab variant became the first of these engines to be fitted to a production car, followed by the Stag V8 in 1970. Sometimes described as two four-cylinder engines siamesed together, it is more strictly correct to say the four-cylinder versions were the left half of a Stag engine.

It has sometimes been alleged Triumph was instructed to use the all-aluminium Rover V8, originally designed by Buick and under development by Rover at the time, but claimed it would not "fit". Installation testing of both the Triumph V8 and the Rover V8 was carried out in May/June 1967, the conclusion being that the engine was too tall and that front structure changes would be necessary. It was decided not to further hold up Stag development and to proceed with the Triumph V8 unit. Although later enthusiasts have shown that it can be made to fit the space, the decision to go with the Triumph V8 was probably more due to the Buick's lack of British sales experience, the fact that there was not a manual gearbox offered by Rover at the time, and that the different torque characteristics and weight would have entailed substantial re-engineering of the Stag when it was already behind schedule. Such a substitution would also have required a rethinking of the wider engineering strategy, both of which were important "fit" considerations beyond the comparatively trivial matter of the relative dimensions of the two engines. Furthermore, Rover, also owned by Leyland Motor Corporation at the time, could not necessarily have supplied the numbers of V8 engines required to match the anticipated production of the Stag.[4]

As in the 2000 model line, unitary construction was employed, as was fully independent suspension: MacPherson struts in front, semi-trailing arms at the rear. Braking was by front disc and rear drum brakes, while steering was power-assisted rack and pinion.


1975 Triumph Stag with alloy wheels
1977 Triumph Stag Mark 2

The car was launched nearly two years late in June 1970, to a warm welcome at the international auto shows. In the UK the Stag was an immediate success for Triumph with a 12-month waiting list rapidly being established and cars changing hands at well above list price, but when it was released into the US, its main target market, it rapidly acquired a reputation for mechanical unreliability, usually in the form of overheating. These problems arose from a variety of causes.

First, the collaboration with Saab on the related slant 4 engine gave rise to design features being carried over to the V8, some of them questionable from an engineering perspective. For example, because the Saab 99 placed the engine back to front in the engine bay, the traditional mounting of the water pump on the front face was not possible. The answer for the Saab engine was to place the water pump within the top of the engine block, which is a higher position than is usual. Due to the use of a common machining line for both the slant 4 and the V8, this positioning was copied to the V8 and led to a situation where if the engine became hot in traffic, and coolant escaped from the cooling system via the expansion bottle, the volume of fluid left when the engine cooled down again fell. If this was not noticed and it continued to occur, it would eventually fall below the level of the pump, which would fail to circulate the coolant and overheating would result. Water pump failures sometimes occurred due to poorly-hardened drive gears, which wore out prematurely and stopped the water pump.[5] Once this key component of the cooling system had failed, overheating ensued.

A second cause of engine trouble was the lack of attention to corrosion inhibitor in the coolant. The block was made from iron and the heads from aluminium, a combination that required the use of corrosion-inhibiting antifreeze all year round. This point was not widely appreciated by owners or by the dealer network supporting them. Consequently, engines were affected by electrolytic corrosion, and white alloy oxide sludge collected in radiator cores, reducing radiator efficiency and again causing overheating. The result was head gasket failure due to cylinder head heat distortion, a very expensive repair. Owners would usually get their repaired cars back with the radiator still clogged, leading to repeat failures.

A third cause of trouble was the engine's use of long, simplex roller link chains, which would first stretch and then often fail inside fewer than 25,000 miles (40,200 km), resulting in expensive damage. Even before failing, a stretched timing chain would skip links and cause valves to lift and fall in the wrong sequence, so that valves hit pistons and damaged both. This fault may have been worsened by poor quality chains.[6]

Another problem with the cylinder heads was said to be the arrangement of cylinder head fixing studs, half of which were vertical and the other half of which were at an angle. Anecdotally, this arrangement was used to reduce production costs, as the cylinder head mounting studs and bolt were all accessible with the rocker covers fitted. This allowed the factory to assemble the cylinder head completely before fitting to the engine. This arrangement worked well enough on the 4-cylinder engines, but in the V8 the angled and vertical studs, when heated and cooled, expanded and contracted in different directions sufficiently to give rise to sideways forces that caused warping of the engine block. The problem was made worse by the engine's propensity to overheat.

Finally, although pre-production engines were built meticulously, those fitted to production cars were not subject to the same careful quality control. Engines are still being discovered with casting sand and core wire inside, blocking the coolant passages and causing overheating.

This combination of manufacturing and maintenance flaws led to some engine failures in the UK but in the US the situation was exacerbated by the need to fit low compression pistons to comply with California's low octane petrol requirements, and the associated advance in ignition timing to meet that country's continually changing emission regulations. The result was that the engine developed greater heat and, when automatic transmission and air conditioning were fitted, the engine cooling ability was overly compromised. Although US cars were fitted with engine cowls to try to compensate, all too often the result of a freeway tailback was an overheating engine. Time magazine rated the Triumph Stag as one of the 50 worst cars ever made.[7]

British Leyland never materially re-engineered the Triumph 3.0 litre OHC V8 to address these issues, other than introducing a domed piston to aid combustion and a high-pressure cooling system that boiled over at a higher temperature. Another problem was that the Stag was always a relatively rare car. British Leyland had around 2,500 UK dealers when the Stag was on sale and a total of around 19,000 were sold in the UK over seven years. Thus the average dealer sold only seven or eight Stags during the car's production run, or roughly one car per year. This meant that few dealers saw defective Stags often enough to recognise and diagnose the cause of the various problems.

A number of owners replaced the troublesome engine with units from other cars, such as the Rover V8, or the Triumph 2.5-litre engine around which the Stag was originally designed. The number of such conversions undertaken is not known, but as at July 2017, 91% of Stags known to DVLA had a 3-litre engine, according to[8] It is not clear how many of these are original Stag engines and how many are Ford 3-litre Essex units. The once-popular Rover V8 conversion powers fewer than 5% of surviving Stags and it is thought by the relevant owners club that the Ford engine figures are much lower than this.

The last production Stag (BOL88V) is kept at the Heritage Motor Centre, Warwickshire.

Mark I and Mark II variants


Perhaps because the American market never took to the Stag, only 25,877 cars were produced between 1970 and 1977. Of this number, 6,780 were export models, of which 2,871 went to the United States. As the Stag was originally destined for large sales in the United States, Triumph utilised the 'model year' method of altering specification details, with each new model year bringing cosmetic changes. For the 1973 model year a number of engineering changes were also made and, although Triumph only ever referred to Stag as one model, since production ceased, enthusiasts have introduced the terms 'Mk 1' and 'Mk 2' to refer to cars produced before and after the 1973 model year change. Model year batches or 'sanctions' are generally identified through differing production numbering sequences, thus, as the first 1973 model year car was chassis numbered 20001, those cars with chassis numbers before 20001 are often referred to as Mk 1 cars and those cars with chassis numbers after 20001 are often referred to as Mk 2 cars.

1973 US-market Mark 2 Stag with factory hardtop installed

When introduced in 1973, the most notable differentiating feature between Mark 1 and Mark 2 Stags was the addition of twin coachlines to the body. At this time the sills and tail panel colour was also altered from body colour to low-gloss black but as the tail panel was altered back again for the 1976 model year, it is not an ideal indicator of the difference between Mk 1 / Mk 2 cars. Inside, Mk 2 cars had a slightly different warning light cluster and the instrument dial needles point up rather than down. They also had a single courtesy light in the T-bar rather than lights at the top of each B-post, the steering wheel was smaller, the seats were upholstered in a different way such that it was possible to fit a simple head restraint (which was initially an optional extra but became a standard fitment later on) and the map-reading light was deleted from the door of the glove box and replaced with an internal light. Very early production cars had a three-quarter window in the soft top, which was deleted during the 1972 model year as it tended to become trapped and then split when stowed. A higher-pressure cooling system was introduced during the 1972 model year. For the 1976 model year the cars returned to having body-colour sills and tail panel, but a stainless steel sill cover, as fitted to all US Stags, was fitted over the sills for all 1976 and 1977 cars. Late Stags fitted with the slightly longer BW65 automatic transmission had a correspondingly shorter propshaft to compensate.

Cars for export markets such as the United States comprised unique combinations of features specifically required for compliance with various states' requirements, or simply for marketing purposes. Cars factory-designated as "Federal specification" included features such as side impact bars in the doors, Federal Department of Transportation compliant lighting, and anti-smog emissions equipment which was not generally found on vehicles for other markets.

Approximately half of the cars built were fitted with a Borg-Warner Type 35 3-speed automatic transmission, which on the last 3,800 vehicles produced gave way to a Type 65. The other choice was a derivative of the ancient Triumph TR2 manual gearbox which had been modified and improved over the years for use in the TR4/A/IRS/TR5/250/6. The first gear ratio was raised and needle roller bearings were used in place of the bronze bushings on the layshaft. Early 4-speed manual transmission models could be ordered with an A-type Laycock overdrive unit and later ones frequently came with a J-type Laycock unit. The overdrive option was often chosen as the engine RPM drops significantly with this option in 3rd and 4th (top) gears, and it was included as a standard fitment for all manual cars from 1973.

Other than the choice of transmissions, there were very few factory-installed options. On early cars, buyers could choose to have the car fitted with just the soft-top, just the hard-top (with the hood stowage compartment empty), or with both. Later cars were supplied as either a 'soft top model' or with both roofs as a 'hard and soft top model'. Three wheel styles were offered. The standard fitment for non US-bound cars from 1970 to 1975 was steel wheels with Rostyle "tin-plate" trims. The wheels are secured with the usual four bolts, but the Rostyle trims have five false bolts. Standard fitment for the US for 1971 and 1972 model years was a 72-spoke wire spoke wheel which was specially designed for Stag. These were possibly available as factory fitments for other markets. For the 1973 model year in the US, five-spoke alloy wheels became the standard fitment and these were also available for other markets. For the 1976 model year, cars for all markets had the alloy wheels fitted as standard.

Electric windows, power steering and power-assisted brakes were standard with Delaney Galley air conditioning being a factory fitted option. A range of aftermarket products including a luggage rack, uprated Koni shock absorbers, floor mats, and Lucas Square Eight fog lamps were available as dealer-installed optional accessories. Part numbers were allocated for leather upholstery but its actual existence is doubtful as it was not included in either the sales brochures or the price lists and no surviving car is known to have original factory leather. Rather unusually for a 4-seat touring car, the parts catalogue included a sump protector plate that was never produced. This was probably included as a slightly "gimmicky" tribute to Triumph's rallying successes.



The Stag was never directly replaced. British Leyland planned an equivalent model to follow the Stag in the form of a derivative of the Triumph TR7 sports car which was codenamed the Lynx. The Lynx used the TR7 platform with an extra 12 inches in the wheelbase to accommodate a rear seat and had fastback coupe bodywork. Power came from a 3.5-litre Rover V8 and the gearbox and rear axle were lifted from the Rover SD1. The Lynx was very close to production being scheduled for launch in 1978. However the sudden closure of the Triumph factory in Speke, Liverpool, where the car was to be built and new policies implemented by BL's new chief executive, Michael Edwardes, led to the Lynx's cancellation.

Unmade variants


Triumph planned a coupé version of the Stag to complement the open-top tourer, in the same manner as the smaller GT6 coupé was based on the Spitfire. In 1968, Michelotti converted his original 1966 styling concept Stag into his idea of a coupe version and, following further deliberations at Triumph, he was sent a prototype body shell for an 'improved' version to be manufactured. This second car took very clear styling cues from the GT6, including the shape of the rear windows and roofline and the provision of air vent 'gills' in the C-pillar. In 1970/71, Triumph built a one-off 'production' Stag coupé, called the Fastback, to Michelotti's design with minor detail differences to match the production Stag more closely. Although the design was considered successful and "more useful than an ordinary Stag",[9] British Leyland did not continue with the project, reportedly because they feared the Stag fastback would take sales from other actual and planned vehicles in the BL range. The Triumph-built prototype survives.

A number of Stags were built with four-wheel drive using the Ferguson Formula developed by Ferguson Research and pioneered on the Jensen FF. One Stag was reportedly fitted with the FF system by Triumph itself during development, but was either scrapped or converted back to standard specification. Two more 4WD Stags were built in 1972 by FF Developments, a company separate from Ferguson that had licensed the technology for converting existing road cars. The cars (one with manual transmission, one with automatic) were commissioned by GKN for development and testing work. Both had automatic locking differentials actuated by a viscous coupling and the same Dunlop Maxaret mechanical anti-lock braking system as used in the Jensen. The cars differed visually from standard by having a broad bulge in the centre of the bonnet; the engine had to be mounted slightly higher in the engine bay to accommodate the drive to the front wheels. Both these cars survive.

A lightweight Stag was tested which was essentially a standard Stag with most of the sound-deadening material removed. This did not proceed. A 32-valve Stag V8 engine was considered, but no documentary or other trace of any actual engine having been built has come to light. Any such engine could not have used two Dolomite Sprint 16-valve heads because it would have required mirror-image heads on opposite sides. Otherwise, the second camshaft, above the opposite bank of cylinders, would have emerged at the wrong end of the engine.[10]

FF Developments also converted a number of Triumph 2000s (saloons and estates) to 4WD, including at least one 'Triumph 3000 estate' which received a Stag engine and gearbox as well as the Ferguson 4WD drivetrain.

Classic status


The Triumph Stag has sizeable club and owner support and a number of specialist suppliers. According to the main UK enthusiast club approximately 8,500 Stags are believed to survive in the United Kingdom. According to DVLA data in Q4 2022, 8,409 UK cars survive, either taxed or under SORN.[8]

Approximately 1,100 Stags are known to have survived in Australia out of the 1,596 originally exported. Most are club registered in their respective states.

Some Stags in Australia and New Zealand have been fitted with the 4.4 Rover V8 made for the Leyland P76.

Notable appearances

Sean Connery in a Mk1 Stag in Diamonds Are Forever
  • In the James Bond film Diamonds Are Forever, Bond commandeers a Saffron Yellow 1970 Stag from a diamond smuggler.
  • The 1978–1979 UK TV series Hazell featured a 1975 Mk2 Stag, originally green, but later repainted red.
  • A 1973 Stag is driven by several characters in the 1985 movie My Beautiful Laundrette.[11]
  • In the 1998 film, Dad Savage, a Carmine Red 1977 Stag is used as an intended getaway vehicle.
  • In the 1981-1991 BBC/Australian TV series Bergerac, a yellow Stag is used by Bergerac's ex-wife Deborah.
  • In the 2000–2001 BBC TV series, Second Sight, DCI Ross Tanner (Clive Owen) drives a Sapphire Blue Stag.
  • In the BBC series New Tricks, retired Detective Sergeant Gerry Standing drives a British racing green 1974 Stag that occasionally gives him trouble.
  • In the 2010, Series 12, Episode 7 of Midsomer Murders, "The Great and the Good", Justin Hooper, played by Bertie Carvel, drives an emerald green Mark III with stainless steel sills.
  • In the 2010, Series 7, Episode 5 of Wheeler Dealers, a 1972 Stag was repaired and sold with a £971 profit.
  • In 2013, during the first series of Channel 4's Car S.O.S., a 1976 Stag is restored in episode 7.
  • In 2014, during the first series of Channel 4's For the Love of Cars, a 1976 Stag is restored in episode 3.
  • A CGI version of a Stag appears in the 2015 film High-Rise. The car seems to be missing its inner headlamps in one shot.
  • In 2016, during the third series of Cuckoo, a 1976 Stag is featured in episode 6, "Sid’s Big Day".
  • In 2021, the Stag plays the main role in Amazon Original Modern Love throughout the first episode of series 2: "On a serpentine road, with the top down".
  • In 2023 the Stag plays in ITV/Mammoth Endeavour as the Mayoress of Oxford’s car stolen by Oxford College ruffians in the second episode of series 9: "Uniform".
  • In the 2023 series of Annika on Masterpiece Theater, Annika’s father drives a yellow Stag in S2 Es4,5,6. At the conclusion of E6 he bequeaths the stag to his granddaughter Morgan.


  1. ^ Robson, Graham (2006). A-Z British Cars 1945–1980. Herridge & Sons. ISBN 0-9541063-9-3. OCLC 77797747.
  2. ^ Culshaw, David J.; Horrobin, Peter J. (1974). Complete Catalogue of British Cars. Macmillan. ISBN 0-333-16689-2. OCLC 1057411.
  3. ^ kato. "Lotus' Own Power Plant". Retrieved 10 July 2018.
  4. ^ "The story of the Buick V8 engine". Retrieved 26 January 2012.
  5. ^ "Technical reprints". Stag Owners Club. p. 45. Archived from the original on 11 October 2017 – via Internet Archive.
  6. ^ Stag Club of New Zealand. "Staying Out of Trouble with a Stag Engine" (PDF). Triumph Stag Engines. Stag Club of New Zealand. Retrieved 20 June 2021.
  7. ^ Neil, Dan (7 September 2007). "The 50 Worst Cars of All". 1970 Triumph Stag. TIME. Retrieved 26 January 2012.
  8. ^ a b . This represents a survival rate of 46.51% of the 17,819 originally registered for UK triumph stag accessed 9 November 2020
  9. ^ Interview with Triumph Director of Engineering Spen King, 1992, cited in Thoroughbred and Classic Cars
  10. ^ Triumph Stag 1970-77 (Choice, Purchase & Performance), James Taylor, 1992; ISBN 1872004172
  11. ^ "Triumph Stag in "My Beautiful Laundrette"". Retrieved 3 January 2022.

Further reading

  • Poole, C. (2004). Genteel Tourer: The Story of the 1970–77 Triumph Stag. Collectible Automobile, October 2004, pp. 52–61.
  • Taylor, James (1999). Original Triumph Stag: The Restorers Guide. pp. 5–15.
  • Taylor, James (1992). Triumph Stag 1970–1977: Choice – Purchase – Performance – #4; Essential Advice & Data for Buyers & Enthusiasts. pp. 6–12.
  • Triumph Service Division, Coventry England. (1969). Triumph British Leyland Preliminary Service Information – STAG, Part Number 545160
  • Standard-Triumph Sales Limited (1969). British Leyland Triumph, Triumph Stag Graphic Catalogue, Graphic Publication no. 519579