Transconductance (for transfer conductance), also infrequently called mutual conductance, is the electrical characteristic relating the current through the output of a device to the voltage across the input of a device. Conductance is the reciprocal of resistance.
It is very often denoted as a conductance, gm, with a subscript, m, for mutual. Transconductance is defined as follows:
Transresistance (for transfer resistance), also infrequently referred to as mutual resistance, is the dual of transconductance. It refers to the ratio between a change of the voltage at two output points and a related change of current through two input points, and is notated as rm:
The SI unit for transresistance is simply the ohm, as in resistance.
Transimpedance (or, transfer impedance) is the AC equivalent of transresistance, and is the dual of transadmittance.
For vacuum tubes, transconductance is defined as the change in the plate(anode)/cathode current divided by the corresponding change in the grid/cathode voltage, with a constant plate(anode)/cathode voltage. Typical values of gm for a small-signal vacuum tube are 1 to 10 millisiemens. It is one of the three characteristic constants of a vacuum tube, the other two being its gain μ (mu) and plate resistance rp or ra. The Van der Bijl equation defines their relation as follows:
Field effect transistorsEdit
Similarly, in field effect transistors, and MOSFETs in particular, transconductance is the change in the drain current divided by the small change in the gate/source voltage with a constant drain/source voltage. Typical values of gm for a small-signal field effect transistor are 1 to 30 millisiemens.
where ID is the DC drain current at the bias point, and VOV is the overdrive voltage, which is the difference between the bias point gate–source voltage and the threshold voltage (i.e., VOV ≡ VGS - Vth).:p. 395, Eq. (5.45) The overdrive voltage (sometimes known as the effective voltage) is customarily chosen at about 70–200 mV for the 65 nm technology node (ID ≈ 1.13 mA/μm of width) for a gm of 11–32 mS/μm.:p. 300, Table 9.2:p. 15, §0127
Additionally, the transconductance for the junction FET is given by , where VP is the pinchoff voltage and IDSS is the maximum drain current.
Traditionally, the transconductance for the FET and MOSFET as given in the equations above is derived from the transfer equation of each device, using calculus. However, Cartwright has shown that this can be done without calculus.
The gm of bipolar small-signal transistors varies widely, being proportional to the collector current. It has a typical range of 1 to 400 millisiemens. The input voltage change is applied between the base/emitter and the output is the change in collector current flowing between the collector/emitter with a constant collector/emitter voltage.
The transconductance for the bipolar transistor can be expressed as
The output (collector) conductance is determined by the Early voltage and is proportional to the collector current. For most transistors in linear operation it is well below 100 µS.
A transconductance amplifier (gm amplifier) puts out a current proportional to its input voltage. In network analysis, the transconductance amplifier is defined as a voltage controlled current source (VCCS) . It is common to see these amplifiers installed in a cascode configuration, which improves the frequency response.
A transresistance amplifier outputs a voltage proportional to its input current. The transresistance amplifier is often referred to as a transimpedance amplifier, especially by semiconductor manufacturers.
The term for a transresistance amplifier in network analysis is current controlled voltage source (CCVS).
A basic inverting transresistance amplifier can be built from an operational amplifier and a single resistor. Simply connect the resistor between the output and the inverting input of the operational amplifier and connect the non-inverting input to ground. The output voltage will then be proportional to the input current at the inverting input, decreasing with increasing input current and vice versa. In practice, the parasitic capacitance of whatever device is connected to the virtual ground of the op-amp may destabilize it, and a compensating capacitance must be added in parallel with the resistor between the output and inverting pins. Arriving at the optimal value of this compensating capacitor can be non-trivial.
Specialist chip transresistance (transimpedance) amplifiers are widely used for amplifying the signal current from photo diodes at the receiving end of ultra high speed fibre optic links. The MAX3724 and MAX3725  are examples.
Operational transconductance amplifiersEdit
An operational transconductance amplifier (OTA) is an integrated circuit which can function as a transconductance amplifier. These normally have an input to allow the transconductance to be controlled.
- Blencowe, Merlin (2009). "Designing Tube Amplifiers for Guitar and Bass".
- Sedra, A.S.; Smith, K.C. (1998), Microelectronic Circuits (Fourth ed.), New York: Oxford University Press, ISBN 0-19-511663-1
- Baker, R. Jacob (2010), CMOS Circuit Design, Layout, and Simulation, Third Edition, New York: Wiley-IEEE, ISBN 978-0-470-88132-3
- Sansen, W.M.C. (2006), Analog Design Essentials, Dordrecht: Springer, ISBN 0-387-25746-2
- Cartwright, Kenneth V (Fall 2009), "Derivation of the Exact Transconductance of a FET without Calculus" (PDF), The Technology Interface Journal, 10 (1): 7 pages