Peening is the process of working a metal's surface to improve its material properties, usually by mechanical means, such as hammer blows, by blasting with shot (shot peening) or blasts of light beams with laser peening. Peening is normally a cold work process, with laser peening being a notable exception. It tends to expand the surface of the cold metal, thereby inducing compressive stresses or relieving tensile stresses already present. Peening can also encourage strain hardening of the surface metal.
This article needs additional citations for verification. (October 2009) (Learn how and when to remove this template message)
Plastic deformation from peening induces a residual compressive stress in a peened surface, along with tensile stress in the interior. This stress state resembles the one seen in toughened glass, and is useful for similar reasons.
Surface compressive stresses confer resistance to metal fatigue and to some forms of corrosion, since cracks will not grow in a compressive environment. The benefit comes at the expense of higher tensile stresses deeper in the part. However, the fatigue properties of the part will be improved, since the stresses are normally significantly higher at the surface in part due to surface imperfections and damage.
Cold work also serves to harden the material's surface. This makes cracks less likely to form at the surface and provides resistance to abrasion. When a metal undergoes strain hardening its yield strength increases but its ductility decreases. Strain hardening actually increases the number of dislocations in the crystal lattice of the material. When a material has a great number of dislocations, plastic deformation is hindered, and the material will continue to behave in an elastic way well beyond the elastic yield stress of the non-strain hardened material.
Residual strain / stretchingEdit
Plastic deformation from peening can be useful in stretching the surface of an object.
One common use of this peening (stretching) process can be seen in the auto repair and auto custom fabrication industries where manual or machine assisted peening is used to stretch thin sheet metal to create curved surfaces. The manual method uses a hand held peening hammer and is a form of planishing. There are also machine assisted methods that use a version of a power hammer to peen the sheet metal.
Another use of the peening process is to flatten sheet metal and is specifically used as a primary technique to flatten steel belts used in industrial conveying and pressing operations. In this process a steel belt that has a cross curvature can be flattened by peening the concave surface to stretch it and thereby removing the cross-curvature by equalizing the surface length across the belt between the previously concave and convex surfaces. The shot peening of steel belts is usually achieved by using specialized equipment and special peening shot.
When peening is used to induce residual stress or work-harden an object, care needs to be taken with thin parts not to stretch the work-piece. Where stretching is unavoidable then allowances may need to be made in the part design or process application.
Use with weldingEdit
Hand peening may also be performed after welding to help relieve the tensile stresses that develop on cooling in the welded metal (as well as the surrounding base metal). The level of reduction in tensile stress is minimal and only occurs on or near to the weld surface. Other methods, like heat spots (if applicable), help reduce residual tensile stresses. Peening will induce a higher hardness into the weld and this is something that should be avoided. For this reason, peening is not normally accepted by the majority of codes, standards or specifications (ex. ASME B31.3 para 328.5.1 (d) location changes when new codes are published). Any peening that is carried out on a weld should have been carried out on the weld procedure qualification test piece.
The welding procedure qualification test piece replicates all of the essential variables that will be used in production welding. If the weld is peened during the qualification of a welding procedure, the subsequent mechanical testing of the procedure qualification test piece will demonstrate the mechanical properties of the weld. These mechanical properties must, as a minimum, match the mechanical properties of the materials that have been welded together. If they do not, the procedure has failed and the welding procedure is not acceptable for use in production welding.
Scythe and sickle blades have traditionally been sharpened by occasional peening followed by frequent honing in the field during use. In the example below, a short scythe blade, being used for clearing brambles, is being sharpened by reforming the malleable steel to create an edge profile that can then be honed. Because this blade is being used to cut tough-stemmed brambles it is being peened after about every thirty hours of work. Nicks and cuts to the blade edge are also worked out of the blade by peening and a new edge profile then formed for honing. A peening jig is used here but blades can be free-peened using various designs of peening anvils. The peening jig shown has two interchangeable caps that set different angles. A coarse angle is set first about 3mm back from the edge and the fine angle is then set on the edge, leaving an edge that lends itself to being easily honed. The blade is then honed using progressively finer honing stones and then taken to the field.
The first published article about peening was written in Germany in 1929, and was specifically about shot peening. The first patent for shot peening was taken out in Germany in 1934, but was never commercially implemented. Independently in 1930, a few engineers at Buick noticed that "shot blasting" (as it was originally termed) made springs resistant to fatigue. This process was then adopted by the automotive industry. Zimmerli first published a report in 1940. John Almen did more research, and during World War 2 introduced it to the aircraft industry.
In the early 1970s peening experienced a major innovation when researchers such as Allan Clauer at Battelle labs in Columbus, Ohio applied high intensity laser beams onto metal components to achieve deep compressive residual stresses, which they patented as Laser Shock Peening, and became known as laser peening in the late 1990s, when it was first applied to gas fired turbine engine fan blades for the U.S. Air Force.
- Fuchs, H. O.; Cary, P. E., History of Shot Peening (PDF), First International Conference on Shot Peening.