Open main menu

The DC-X, short for Delta Clipper or Delta Clipper Experimental, was an uncrewed prototype of a reusable single-stage-to-orbit launch vehicle built by McDonnell Douglas in conjunction with the United States Department of Defense's Strategic Defense Initiative Organization (SDIO) from 1991 to 1993. Starting 1994 until 1995, testing continued through funding of the US civil space agency NASA.[1] In 1996, the DC-X technology was completely transferred to NASA, which upgraded the design for improved performance to create the DC-XA.

McDonnell Douglas DC-XA Reusable Launch Vehicle (RLV) concept
FunctionPrototype SSTO vehicle
ManufacturerMcDonnell Douglas (Huntington Beach, California)
Country of originUnited States
Project cost$ 60 million (1991)
Height12 metres (39 ft)
Diameter4.1 metres (13 ft)
Mass18,900 kilograms (41,700 lb)
Launch history
Launch sitesWhite Sands Missile Range
Total launches12
Partial failures3
First flight18 August 1993
Last flight31 July 1996
First stage
Diameter4.1 metres (13 ft)
Empty mass9,100 kilograms (20,100 lb)
Gross mass18,900 kilograms (41,700 lb)
EnginesFour RL-10A-5 liquid-fueled rocket engines
four gaseous oxygen/gaseous hydrogen thrusters
ThrustMain rockets, 60 kN (13,000 lbf)
Thrusters, 2.0 kN (440 lbf)
FuelLiquid oxygen and liquid hydrogen


According to writer Jerry Pournelle: "DC-X was conceived in my living room and sold to National Space Council Chairman Dan Quayle by General Graham, Max Hunter and me." According to Max Hunter, however, he had tried hard to convince Lockheed Martin of the concept's value for several years before he retired.[2] Hunter had written a paper in 1985 entitled "The Opportunity", detailing the concept of a Single-Stage-To-Orbit spacecraft built with low-cost "off-the-shelf" commercial parts and currently-available technology,[3] but Lockheed Martin was not interested enough to fund such a program themselves.

On February 15, 1989, Pournelle, Graham and Hunter were able to procure a meeting with Vice-President Dan Quayle. They "sold" the idea to SDIO by noting that any space-based weapons system would need to be serviced by a spacecraft that was far more reliable than the Space Shuttle, and offer lower launch costs and have much better turnaround times.[citation needed]

Given the uncertainties of the design, the basic plan was to produce a deliberately simple test vehicle and to "fly a little, break a little" in order to gain experience with fully reusable quick-turnaround spacecraft. As experience was gained with the vehicle, a larger prototype would be built for sub-orbital and orbital tests. Finally a commercially acceptable vehicle would be developed from these prototypes. In keeping with general aircraft terminology, they proposed the small prototype should be called the DC-X, X being the US Air Force designation for "experimental". This would be followed by the "DC-Y", Y being the USAF designation for pre-production test aircraft and prototypes (i.e YF-16, etc). Finally the production version would be known as the "DC-1". The name "Delta Clipper" was chosen deliberately to result in the acronym "DC" to draw a connection with the Douglas "DC Series" of airliners, beginning with the Douglas DC-2 and its more famous development, the Douglas DC-3, which many credit with being the first modern airliner and revolutionizing air travel (the series continued with the DC-4, DC-5, DC-6, DC-7, DC-8, DC-9, and DC-10). In the case of the airliners, "DC" stood for "Douglas Commercial".[citation needed]

SDIO requirementEdit

SDIO wanted a "suborbital, recoverable rocket (SRR) capable of lifting up to 3,000 pounds (1361 kg) of payload to an altitude of 1.5 million feet (457 km); returning to the launch site for a precise soft landing; with the capability to launch for another mission within three to seven days".[4]:4


DC-X Specifications:[5]

  • 12 m high, 4.1 m diameter at base, conical shape
  • Empty mass: 9100 kg. Fuelled mass: With full load of propellants:18,900 kg
  • Propellants: Liquid oxygen and liquid hydrogen
  • Propulsion: Four RL10A5 rocket engines, each generating 6,100 kgf thrust. Each engine throttleable from 30% to 100%. Each gimbals +/-8 degrees.
  • Reaction Controls: Four 440-lb thrust gaseous oxygen, gaseous hydrogen thrusters
  • Guidance, Navigation and Control Avionics: Advanced 32 bit, 4.5 mips computer, F-15 Navigation System with ring laser gyros. F/A-18 accelerometer and rate gyro package. Global Positioning Satellite P(Y) code receiver. Digital data telemetry system. Radar altimeter.
  • Hydraulic System: Standard hydraulic aircraft-type system to drive vehicle's five aerodynamic flaps and eight engine gimbal actuators (two per engine).
  • Construction Materials: Aeroshell and base heat shield: Graphitic Epoxy composite with special silicone-based thermal protection coating; Main propellant tanks: 2219 alloy aluminium; Main structural supports: aluminium; Landing gear: steel and titanium


Built as a one-third-size scale prototype,[6] the DC-X was never designed to achieve orbital altitudes or velocity, but instead to demonstrate the concept of vertical take off and landing. The vertical take off and landing concept was popular in science fiction films from the 1950s (Rocketship X-M, Destination Moon, and others), but not seen in real world designs of space vehicles (although the Falcon 9 rocket built by SpaceX features an automated vertical landing cycle for the first stage booster; this is not a "space vehicle" though, as it never leaves the atmosphere). It would take off vertically like standard rockets, but also land vertically with the nose up. This design used attitude control thrusters and retro rockets to control the descent, allowing the craft to begin atmospheric entry nose-first, but then roll around and touch down on landing struts at its base. The craft could be refueled where it landed, and take off again from exactly the same position — a trait that allowed unprecedented turnaround times (although in practice the process of recovering a spacecraft and transporting it back to the launch site and setting it up again take far less time than refueling, systems checks, repair of heat resistant surfaces, etc).[citation needed]

In theory a base-first re-entry profile would be easier to arrange. The base of the craft would already need some level of heat protection to survive the engine exhaust, so adding more protection would be easy enough. More importantly, the base of the craft is much larger than the nose area, leading to lower peak temperatures as the heat load is spread out over a larger area. Finally, this profile would not require the spacecraft to "flip around" for landing.[citation needed]

The military role made this infeasible, however. One desired safety requirement for any spacecraft is the ability to "abort once around", that is, to return for a landing after a single orbit. Since a typical low Earth orbit takes about 90 to 120 minutes, the Earth will rotate to the east about 20 to 30 degrees in that time; or for a launch from the southern United States, about 1,500 miles (2,400 km). If the spacecraft is launched to the east this does not present a problem, but for the polar orbits required of military spacecraft, when the orbit is complete the spacecraft overflies a point far to the west of the launch site. In order to land back at the launch site, the craft needs to have considerable cross-range maneuverability, something that is difficult to arrange with a large smooth surface. The Delta Clipper design thus used a nose-first re-entry with flat sides on the fuselage and large control flaps to provide the needed cross range capability. Experiments with the control of such a re-entry profile had never been tried, and were a major focus of the project.[citation needed]

Another focus of the DC-X project was minimized maintenance and ground support. To this end, the craft was highly automated and required only three people in its control center (two for flight operations and one for ground support). In some ways the DC-X project was less about technology research than operations.[citation needed]

Flight testingEdit

The Delta Clipper Advanced
First flight
First landing. The yellow exhaust is due to the low throttle settings, which burns at lower temperatures and is generally "dirty" as a result.

Construction of the DC-X started in 1991 at McDonnell Douglas' Huntington Beach facility. The aeroshell was custom-constructed by Scaled Composites, but the majority of the spacecraft was built from commercial off-the-shelf parts, including the engines and flight control systems.[citation needed]

The DC-X first flew, for 59 seconds, on 18 August 1993. It flew two more flights 11 September and 30 September, when funding ran out as a side effect of the winding down of the SDIO program. Apollo astronaut Pete Conrad was at the ground-based controls for some flights.[7] These tests were conducted at the White Sands Missile Range in New Mexico.

Further funding was provided by NASA and the Advanced Research Projects Agency (ARPA) however,[1] and the test program restarted on 20 June 1994 with a 136-second flight. The next flight, 27 June 1994, suffered an inflight (minor) explosion, but the craft successfully executed an abort and autoland. Testing restarted after this damage was fixed, and three more flights were carried out on 16 May 1995, 12 June, and 7 July. On the last flight a hard landing cracked the aeroshell. By this point funding for the program had already been cut, and there were no funds for the needed repairs.[8] The altitude record for the DC-X was 2,500 m, set during its last flight before upgrading to the DC-XA, on 7 July 1995 [8]


NASA agreed to take on the program after the last DC-X flight in 1995. In contrast to the original concept of the DC-X demonstrator, NASA applied a series of major upgrades to test new technologies. In particular, the oxygen tank was replaced by a lightweight (alloy 1460 equivalent of alloy 2219) aluminium-lithium alloy tank from Russia, and the fuel tank by a newer composite design. The control system was likewise improved. The upgraded vehicle was called the DC-XA, renamed the Clipper Advanced/Clipper Graham, and resumed flight in 1996.[citation needed]

The first flight of the DC-XA test vehicle was made on 18 May 1996 and resulted in a minor fire when the deliberate "slow landing" resulted in overheating of the aeroshell. The damage was quickly repaired and the vehicle flew two more times on 7 and 8 June, a 26-hour turnaround. On the second of these flights the vehicle set its altitude and duration records, 3,140 metres (10,300 ft) and 142 seconds of flight time. Its next flight, on 7 July, proved to be its last. During testing, one of the LOX tanks had been cracked. When a landing strut failed to extend due to a disconnected hydraulic line, the DC-XA fell over and the tank leaked. Normally the structural damage from such a fall would constitute only a setback, but the LOX from the leaking tank fed a fire which severely burned the DC-XA, causing such extensive damage that repairs were impractical.[8]

In a post-accident report, NASA's Brand Commission blamed the accident on a burnt-out field crew who had been operating under on-again/off-again funding and constant threats of outright cancellation. The crew, many of them originally from the SDIO program, were also highly critical of NASA's "chilling" effect on the program, and the masses of paperwork NASA demanded as part of the testing regimen.[citation needed]

NASA had taken on the project grudgingly after having been "shamed" by its very public success under the direction of the SDIO. Its continued success was cause for considerable political in-fighting within NASA due to it competing with their "home grown" Lockheed Martin X-33/VentureStar project. Pete Conrad priced a new DC-X at $50 million, cheap by NASA standards, but NASA decided not to rebuild the craft in light of budget constraints.[8]

Rather, NASA focused development on the Lockheed Martin VentureStar which it felt answered some criticisms of the DC-X; specifically the requirement that many NASA engineers preferred the airplane-like landing of the VentureStar over the vertical landing of the DC-X. Just a few years later, the repeated failure of the Venturestar project, especially the composite LH2 (liquid hydrogen) tank, led to program cancellation.[9]

Program costEdit

The original DC-X was built in 21 months for a cost of $60 million.[10]:6

At the time of cancellation, the project[clarification needed] had existed for 21 months,[dubious ] requiring a team of 100 people, at a cost of around $60 million [10] in 1991 dollars.[5] This is equivalent to $110 million in present-day (2014) terms.[11]


Several engineers who worked on the DC-X were hired by Blue Origin, and their New Shepard vehicle was inspired by the DC-X design.[12] Blue Origin does not require the high cross range capabilities, and therefore uses a base-first re-entry profile. Also, the DC-X provided inspiration for many elements of Armadillo Aerospace's, Masten Space Systems's, and TGV Rockets's spacecraft designs.[citation needed]

Some NASA engineers[who?] believe that the DC-X could provide a solution for a crewed Mars lander. Had a DC-type craft been developed that operated as an SSTO in Earth's gravity well, even if with only a minimum 4–6 crew capacity, variants of it might prove extremely capable for both Mars and Moon missions. Such a variant's basic operation would have to be "reversed"; from taking off and then landing, to landing first then taking off. Yet, if this could be accomplished on Earth, the weaker gravity found at both Mars and the Moon would make for dramatically greater payload capabilities, particularly at the latter destination.[citation needed]

Some people proposed design changes include using an oxidizer/fuel combination that does not require the relatively extensive ground support required for the liquid hydrogen and liquid oxygen that DC-X utilized, and adding a fifth leg for increased stability during and after landing.[citation needed]

See alsoEdit


  1. ^ a b "DELTA CLIPPER TEST PROGRAM OFF TO FLYING START". Retrieved 2012-01-16.
  2. ^ Statement by Max Hunter, White Sands, May 16, 1995 in conversation with Dave Klingler
  3. ^ The Rise and Fall of the SDIO's SSTO Program, From the X-Rocket to the Delta Clipper", Andrew J. Butrica, NASA
  4. ^ Environmental Assessment (for) Single Stage Rocket Technology DC-X Test Program June 1992 147 pages
  5. ^ a b "DCX". Archived from the original on December 28, 2012. Retrieved January 4, 2013. Cite uses deprecated parameter |deadurl= (help)
  6. ^ Chris ‘Xenon Hanson. "About the DC-X". Archived from the original on 2002-10-23. Cite uses deprecated parameter |dead-url= (help)
  7. ^ Klerkx, Greg: Lost in Space: The Fall of NASA and the Dream of a New Space Age, page 104. Secker & Warburg, 2004
  8. ^ a b c d "The Delta Clipper Experimental: Flight Testing Archive". NASA; McDonnell Douglas. 6 January 1998.
  9. ^ "VentureStar by Lockheed Martin in Orbit - Computer Graphic". May 1996.
  10. ^ a b Jason Moore & Ashraf Shaikh (Dec 2003). "Delta Clipper – A Path to the Future" (PDF). University of Texas, Austin. Retrieved January 4, 2013.
  11. ^ Federal Reserve Bank of Minneapolis. "Consumer Price Index (estimate) 1800–". Retrieved January 2, 2019.
  12. ^ "A Secretive Aerospace Company Sheds a Bit of Light on Its Rocket Program". 2007-01-09. Retrieved 2018-09-23.

External linksEdit