This article relies largely or entirely on a single source. (December 2009)
A manual is a musical keyboard designed to be played with the hands, on an instrument such as a pipe organ, harpsichord, clavichord, electronic organ, or synthesizer. The term "manual" is used with regard to any hand keyboard on these instruments to distinguish it from the pedalboard, which is a keyboard that the organist plays with their feet. It is proper to use "manual" rather than "keyboard", then, when referring to the hand keyboards on any instrument that has a pedalboard.
Music written to be played only on the manuals (instead of using the pedals) can be designated by manualiter (first attested in 1511, but particularly common in the 17th and 18th centuries).
Organs and synthesizers can, and usually do, have more than one manual; most home instruments have two manuals, while most larger organs have two or three. Elaborate pipe organs and theater organs can have four or more manuals. The manuals are set into the organ console (or "keydesk").
The layout of a manual is roughly the same as a piano keyboard, with long, usually ivory or light-colored keys for the natural notes of the Western musical scale, and shorter, usually ebony or dark-colored keys for the five sharps and flats. A typical, full-size organ manual consists of five octaves, or 61 keys. Piano keyboards, by contrast, normally have 88 keys; some electric pianos and digital pianos have fewer keys, such as 61 or 73 keys. Some smaller electronic organs may have manuals of four octaves or less (25, 49, 44, or even 37 keys). Changes in registration through use of drawknobs, stop tabs, or other mechanisms to control organ stops allow such instruments to achieve an aggregate range well in excess of pianos and other keyboard instruments even with manuals of shorter pitch range and smaller size.
On smaller electronic organs and synthesizers, the manuals may span fewer octaves, and they may also be offset, with the lower one an octave to the left of the upper one. This arrangement encourages the organist to play the melody line on the upper manual while playing the harmony line, chords or bassline on the lower manual.
On pipe organs each manual plays a specific subset of the organ's stops, and electric organs (e.g., Hammond organ) and electronic organs can emulate this style of play. Hammond organs differ from pipe organs in that pipe organs can only pull a stop out (that is, turn on a stop) or push it in (turning off this stop); in contrast, Hammond organs typically have drawbars, so that the player can control how much of each "pipe rank" (e.g., 16', 8', 4', 2', etc.) they wish to use. Synthesizers can program separate manuals to emulate sounds of various orchestral sections or instruments, using imitative digital sounds or sampling of real instruments, or using entirely synthesized sounds. On digital synthesizer instruments a performer can produce the sounds of an entire orchestra through the use of all available manuals in conjunction with the pedalboard and the various registration controls.
Organ manuals vs. piano keyboardsEdit
Despite the superficial resemblance to piano keyboards, organ manuals require a very different style of playing. Organ keys often require less force to depress than piano keys. When depressed, an organ key continues to sound its note at the same volume until the organist releases the key, unlike a piano key, whose note gradually fades away as the string vibrations fade away. On the other hand, while the pianist may allow the piano notes to continue to sound for a few moments after lifting their hands from the keys by depressing the sustain pedal, most organs have no corresponding control; the note invariably ceases when the organist releases the key. The exception is some modern electronic instruments and relatively contemporary upgrades to theatre pipe organ consoles, which may have a knee lever which sustains the previous chords or notes. The knee lever enables an organist to hold a chord or note during a fermata or cadence, thus freeing up their hands to turn a page in the sheet music, change stops, conduct a choir or orchestra, or shift hands to another manual.
Another difference is that of dynamic control. Unlike the case of piano keys, the force with which the organist depresses the key has no relation to the note’s resonance; instead, the organist controls the volume through use of the expression pedals. While the piano note, then, can only decay, the organ note may increase in volume or undergo other dynamic changes. Some modern electronic instruments allow for volume to vary with the force applied to the key and permit the organist to sustain the note and alter both its attack and decay in a variety of ways. For example, Hammond organs often have an expression pedal, which enables the performer to increase or decrease the volume of a note, chord, or passage. All of these variables mean that both the technique of organ playing and the resulting music are quite different from those of the piano. Nevertheless, the trained pianist may play a basic organ repertoire with little difficulty, although more advanced organ music will require specialized training and practice, as the musician has to learn to play on multiple manuals, set stops and other controls while performing, and play the pedal keyboard with the feet.
One of the key types of electromechanical organs, the Hammond B-3, has two manuals. Each manual has drawbars which are used to control the registration for each manuals.
Common names of manuals on pipe organs include Great, Choir, Swell, Solo and Echo in English; Grand Orgue, Positif, Récit and Echo in French; Hauptwerk, Rückpositiv, Brustwerk and Oberwerk in German; and Hoofdwerk, Rugwerk, Borstwerk and Bovenwerk in Dutch. Theatre pipe organs use the nomenclature Great, Accompaniment, Solo, Bombarde, and Orchestral.
Various other controls, such as stops, pistons, and registration presets are usually located adjacent to the manuals to allow the organist ready access to them while playing. This further increases the instrument’s versatility, as a piston or other preset function can cause multiple stops to be pulled out or pushed in automatically. This is of particular benefit in pieces where a number of stops have to be pulled out or pushed in between sections. Devices known as couplers are sometimes available to link the manuals, so that the stops (and pipes) normally played on one can be played from another.