Lithium ion manganese oxide battery
A lithium ion manganese oxide battery (LMO) is a lithium ion cell that uses manganese dioxide, MnO
2, as the cathode material. They function through the same intercalation/de-intercalation mechanism as other commercialized secondary battery technologies, such as LiCoO
2. Cathodes based on manganese-oxide components are earth-abundant, inexpensive, non-toxic, and provide better thermal stability.
One of the more studied manganese oxide-based cathodes is LiMn
4, a cation ordered member of the spinel structural family (space group Fd3m). In addition to containing inexpensive materials, the three-dimensional structure of LiMn
4 lends itself to high rate capability by providing a well connected framework for the insertion and de-insertion of Li+
ions during discharge and charge of the battery. In particular, the Li+
ions occupy the tetrahedral sites within the Mn
4 polyhedral frameworks adjacent to empty octahedral sites.  As a consequence of this structural arrangement, batteries based on LiMn
4 cathodes have demonstrated a higher rate-capability compared to materials with two-dimensional frameworks for Li+
A significant disadvantage of cathodes based on LiMn
4 is the surface degradation observed when the average oxidation state of the manganese drops below Mn+3.5. At this concentration, the formally Mn(III) at the surface can disproportionate to form Mn(IV) and Mn(II) by the Hunter mechanism. The Mn(II) formed is soluble in most electrolytes and its dissolution degrades the cathode. With this in mind many manganese cathodes are substituted or doped to keep the average manganese oxidation state above +3.5 during battery use or they will suffer from lower overall capacities as a function of cycle life and temperature 
3 is a lithium rich layered rocksalt structure that is made of alternating layers of lithium ions and lithium and manganese ions in a 1:2 ratio, similar to the layered structure of LiCoO
2. In the nomenclature of layered compounds it can be written Li(Li0.33Mn0.67)O2.  Although Li
3 is electrochemically inactive, it can be charged to a high potential (4.5 V v.s Li0) in order to undergo lithiation/de-lithiation or delithiated using an acid leaching process followed by mild heat treatment.  However, extracting lithium from Li
3 at such a high potential can also be charge compensated by loss of oxygen from the electrode surface which leads to poor cycling stability. New allotropes of Li
3 have been discovered which have better structural stability against oxygen release (longer cycle-life).
The layered manganese oxide LiMnO
2 is constructed from corrugated layers of manganese/oxide octahedra and is electrochemically unstable. The distortions and deviation from truly planar metal oxide layers are a manifestation of the electronic configuration of the Mn(III) Jahn-Teller ion. A layered variant, isostructural with LiCoO2, was prepared by Armstrong and Bruce in 1996 by ion exchange from the layered compound NaMnO2, however long term cycling and the defect nature of the charged compound led to structural degradation and cation equilibration to other phases.
The layered manganese oxide Li
2 is structurally related to Li
3 and LiCoO2 with similar transition metal oxide layers separated by a layer containing two lithium cations occupying the available two tetrahedral sites in the lattice rather the one octahedral site. The material is typically made by low voltage lithiation of the parent compound, direct lithiation using liquid ammonia, or via use of an organic lithiating reagent. Stability on cycling has been demonstrated in symmetric cells although due to Mn(II) formation and dissolution cycling degradation is expected. Stabilization of the structure using dopants and substitutions to decrease the amount of reduced manganese cations has been a successful route to extending the cycle life of these lithium rich reduced phases. These layered manganese oxide layers are so rich in lithium.
3 • y Li
4 • z LiMnO2 CompositesEdit
One of the main research efforts in the field of lithium-manganese oxide electrodes for lithium-ion batteries involves developing composite electrodes using structurally integrated layered Li
3, layered LiMnO2, and spinel LiMn
4, with a chemical formula of x Li
3 • y Li
4 • z LiMnO2, where x+y+z=1. The combination of these structures provides increased structural stability during electrochemical cycling while achieving higher capacity and rate-capability. A rechargeable capacity in excess of 250 mAh/g was reported in 2005 using this material, which has nearly twice the capacity of current commercialized rechargeable batteries of the same dimensions. 
- Thackeray, Michael M. "Manganese oxides for lithium batteries." Progress in Solid State Chemistry 25.1 (1997): 1-71.
- M. M. Thackeray, P.J. Johnson, L.A. de Picciotto, P.G. Bruce, J.B. Goodenough. "Electrochemical extraction of lithium from LiMn2O 4" Materials Research Bulletin 19.2 (1984): 179-187
- M. M. Thackeray, Yang Shao‐Horn, Arthur J Kahaian, Keith D Kepler, Eric Skinner, John T Vaughey, Stephen A Hackney "Structural Fatigue in Spinel Electrodes in High Voltage (4 V) Li/LixMn2O4 Cells" Electrochemical and Solid-State Letters 1 (1), 7-9 (1998)
- M. Lanz, C. Kormann, H. Steininger, G. Heil, O. Haas, P.Novak, J. Electrochem. Soc. 147 (2000) 3997.
- J. C. Hunter, J. Solid State Chem., 39, 142 (1981)
- A. Du Pasquier, A. Blyr, P. Courjal, D. Larcher, G. Amatucci,B. Gerand, J.M. Tarascon, J. Electrochem. Soc. 146 (1999) 428
- Michael M. Thackeray,Christopher S. Johnson, John T. Vaughey, N. Li, Stephen A. Hackney "Advances in manganese-oxide ‘composite’electrodes for lithium-ion batteries." Journal of Materials Chemistry 15.23 (2005): 2257-2267.
- P. Kalyani, S. Chitra, T. Mohan and S. Gopukumar, J. Power Sources, 1999, 80, 103.
- Jinsub Lim, Jieh Moon, Jihyeon Gim,Sungjin Kim,Kangkun Kim,Jinju Song Jungwon Kang,Won Bin Im, Jaekook Kim "Fully activated Li2MnO3 nanoparticles by oxidation reaction" J. Mater. Chem., 2012,22, 11772-11777(2012); DOI: 10.1039/C2JM30962A
- A. Robertson and P. G. Bruce, Chem. Mater., 2003, 15, 1984.
- Shuo Wang, Junyi Liu and Qiang Sun "New allotropes of Li2MnO3 as cathode materials with better cycling performance predicted in high pressure synthesis" Journal of Materials Chemistry A, 2017,5, 16936-16943; DOI: 10.1039/C7TA04941B
- I. Koetschau, M. N. Richard, J. R. Dahn, J. B. Soupart, J. C. Rousche "Orthorhombic LiMnO2 as a High Capacity Cathode for Li‐Ion Cells" J. Electrochemical Society volume 142(9) 2906-2910 (1995); doi: 10.1149/1.2048663
- A. Robert Armstrong, Peter G. Bruce "Synthesis of layered LiMnO2 as an electrode for rechargeable lithium batteries" Nature 381, p 499–500(1996)DOI: 10.1038/381499a0
- Christopher S Johnson, Jeom-Soo Kim, A Jeremy Kropf, Arthur J Kahaian, John T Vaughan, Michael M Thackeray "The role of Li2MO2 structures (M= metal ion) in the electrochemistry of (x) LiMn0.5Ni0.5O2·(1− x) Li2TiO3 electrodes for lithium-ion batteries" Electrochemistry Communications 4 (6), 492-498 (2002)
- Johnson, C. S., N. Li, J.T. Vaughey, S.A. Hackney, M.M. Thackeray "Lithium–manganese oxide electrodes with layered–spinel composite structures x Li
3·(1− x) Li
4 (0< x< 1, 0⩽ y⩽ 0.33) for lithium batteries." Electrochemistry communications 7.5 (2005): 528-536.
- C. S. Johnson, J. T. Vaughey, M. M. Thackeray, T. E. Bofinger, and S. A. Hackney "Layered Lithium-Manganese Oxide Electrodes Derived from Rock-Salt LixMnyOz (x+y=z) Precursors" 194th Meeting of the Electrochemical Society, Boston, MA, Nov.1-6, (1998)