Gyroscope(Redirected from Gyroscopic)
A gyroscope (from Ancient Greek γῦρος gûros, "circle" and σκοπέω skopéō, "to look") is a device used for measuring or maintaining orientation and angular velocity. It is a spinning wheel or disc in which the axis of rotation is free to assume any orientation by itself. When rotating, the orientation of this axis is unaffected by tilting or rotation of the mounting, according to the conservation of angular momentum.
Gyroscopes based on other operating principles also exist, such as the microchip-packaged MEMS gyroscopes found in electronic devices, solid-state ring lasers, fibre optic gyroscopes, and the extremely sensitive quantum gyroscope. 
Applications of gyroscopes include inertial navigation systems, such as in the Hubble telescope, or inside the steel hull of a submerged submarine. Due to their precision, gyroscopes are also used in gyrotheodolites to maintain direction in tunnel mining. Gyroscopes can be used to construct gyrocompasses, which complement or replace magnetic compasses (in ships, aircraft and spacecraft, vehicles in general), to assist in stability (bicycles, motorcycles, and ships) or be used as part of an inertial guidance system.
MEMS gyroscopes are popular in some consumer electronics, such as smartphones.
Description and diagramEdit
A gyroscope is a wheel mounted in two or three gimbals, which are pivoted supports that allow the rotation of the wheel about a single axis. A set of three gimbals, one mounted on the other with orthogonal pivot axes, may be used to allow a wheel mounted on the innermost gimbal to have an orientation remaining independent of the orientation, in space, of its support. In the case of a gyroscope with two gimbals, the outer gimbal, which is the gyroscope frame, is mounted so as to pivot about an axis in its own plane determined by the support. This outer gimbal possesses one degree of rotational freedom and its axis possesses none. The inner gimbal is mounted in the gyroscope frame (outer gimbal) so as to pivot about an axis in its own plane that is always perpendicular to the pivotal axis of the gyroscope frame (outer gimbal). This inner gimbal has two degrees of rotational freedom. The gyroscope can be easily calibrated with an outer ring and subsequently used to measure the curvature of open solids. Originally, these instruments were primarily used by opticians to measure the curvature of the surface of a lens.. The usual form consists of a fine screw moving in a nut carried on the center of a 3 small legged table or frame; the feet forming the vertices of an equilateral triangle. The lower end of the screw and those of the table legs are finely tapered and terminate in hemispheres, so that each rests on a point. If the screw has two turns of the thread to the millimetre the head is usually divided into 50 equal parts, so that differences of 0.01 millimeter may be measured without using a vernier. A lens, however, may be fitted, in order to magnify the scale divisions. A vertical scale fastened to the table indicates the number of whole turns of the screw and serves as an index for reading the divisions on the head.
A contact-lever, delicate level or electric contact arrangement may be attached to the spherometer in order to indicate the moment of touching more precisely than is possible by the sense of touch. To measure the radius of a sphere—e.g. the curvature of a lens—the device is leveled and read, then placed on the sphere, adjusted until the four points exert equal pressure, and read again. The difference gives the thickness of that portion of the sphere cut off by a plane passing through the three
The axle of the spinning wheel defines the spin axis. The rotor is constrained to spin about an axis, which is always perpendicular to the axis of the inner gimbal. So the rotor possesses three degrees of rotational freedom and its axis possesses two. The wheel responds to a force applied to the input axis by a reaction force to the output axis.
The behaviour of a gyroscope can be most easily appreciated by consideration of the front wheel of a bicycle. If the wheel is leaned away from the vertical so that the top of the wheel moves to the left, the forward rim of the wheel also turns to the left. In other words, rotation on one axis of the turning wheel produces rotation of the third axis.
A gyroscope flywheel will roll or resist about the output axis depending upon whether the output gimbals are of a free or fixed configuration. Examples of some free-output-gimbal devices would be the attitude reference gyroscopes used to sense or measure the pitch, roll and yaw attitude angles in a spacecraft or aircraft.
The centre of gravity of the rotor can be in a fixed position. The rotor simultaneously spins about one axis and is capable of oscillating about the two other axes, and it is free to turn in any direction about the fixed point (except for its inherent resistance caused by rotor spin). Some gyroscopes have mechanical equivalents substituted for one or more of the elements. For example, the spinning rotor may be suspended in a fluid, instead of being mounted in gimbals. A control moment gyroscope (CMG) is an example of a fixed-output-gimbal device that is used on spacecraft to hold or maintain a desired attitude angle or pointing direction using the gyroscopic resistance force.
In some special cases, the outer gimbal (or its equivalent) may be omitted so that the rotor has only two degrees of freedom. In other cases, the centre of gravity of the rotor may be offset from the axis of oscillation, and thus the centre of gravity of the rotor and the centre of suspension of the rotor may not coincide.
Essentially, a gyroscope is a top combined with a pair of gimbals. Tops were invented in many different civilizations, including classical Greece, Rome, and China. Most of these were not utilized as instruments.
The first known apparatus similar to a gyroscope (the "Whirling Speculum" or "Serson's Speculum") was invented by John Serson in 1743. It was used as a level, to locate the horizon in foggy or misty conditions.
The first instrument used more like an actual gyroscope was made by Johann Bohnenberger of Germany, who first wrote about it in 1817. At first he called it the "Machine". Bohnenberger's machine was based on a rotating massive sphere. In 1832, American Walter R. Johnson developed a similar device that was based on a rotating disc. The French mathematician Pierre-Simon Laplace, working at the École Polytechnique in Paris, recommended the machine for use as a teaching aid, and thus it came to the attention of Léon Foucault. In 1852, Foucault used it in an experiment involving the rotation of the Earth. It was Foucault who gave the device its modern name, in an experiment to see (Greek skopeein, to see) the Earth's rotation (Greek gyros, circle or rotation), which was visible in the 8 to 10 minutes before friction slowed the spinning rotor.
In the 1860s, the advent of electric motors made it possible for a gyroscope to spin indefinitely; this led to the first prototype heading indicators, and a rather more complicated device, the gyrocompass. The first functional gyrocompass was patented in 1904 by German inventor Hermann Anschütz-Kaempfe. American Elmer Sperry followed with his own design later that year, and other nations soon realized the military importance of the invention—in an age in which naval prowess was the most significant measure of military power—and created their own gyroscope industries. The Sperry Gyroscope Company quickly expanded to provide aircraft and naval stabilizers as well, and other gyroscope developers followed suit.
In 1917, the Chandler Company of Indianapolis, created the "Chandler gyroscope", a toy gyroscope with a pull string and pedestal. Chandler continued to produce the toy until the company was purchased by TEDCO inc. in 1982. The chandler toy is still produced by TEDCO today.
In the first several decades of the 20th century, other inventors attempted (unsuccessfully) to use gyroscopes as the basis for early black box navigational systems by creating a stable platform from which accurate acceleration measurements could be performed (in order to bypass the need for star sightings to calculate position). Similar principles were later employed in the development of inertial navigation systems for ballistic missiles.
During World War II, the gyroscope became the prime component for aircraft and anti-aircraft gun sights. After the war, the race to miniaturize gyroscopes for guided missiles and weapons navigation systems resulted in the development and manufacturing of so-called midget gyroscopes that weighed less than 3 ounces (85 g) and had a diameter of approximately 1 inch (2.5 cm). Some of these miniaturized gyroscopes could reach a speed of 24,000 revolutions per minute in less than 10 seconds.
Gyroscopes continue to be an engineering challenge. For example, the axle bearings have to be extremely accurate. A small amount of friction is deliberately introduced to the bearings, since otherwise an accuracy of better than of an inch would be required.
Three-axis MEMS-based gyroscopes are also being used in portable electronic devices such as tablets, smartphones, and smartwatches. This adds to the 3-axis acceleration sensing ability available on previous generations of devices. Together these sensors provide 6 component motion sensing; acceleration for X,Y, and Z movement, and gyroscopes for measuring the extent and rate of rotation in space (roll, pitch and yaw). Some devices (e.g. the iPhone) additionally incorporate a magnetometer to provide absolute angular measurements relative to the Earth's magnetic field. Newer MEMS-based inertial measurement units incorporate up to all nine axes of sensing in a single integrated circuit package, providing inexpensive and widely available motion sensing.
A Steadicam rig was employed during the filming of Return of the Jedi, in conjunction with two gyroscopes for extra stabilization, to film the background plates for the speeder bike chase. Steadicam inventor Garrett Brown operated the shot, walking through a redwood forest, running the camera at one frame per second. When projected at 24 frames per second, it gave the impression of flying through the air at perilous speeds.
The heading indicator or directional gyro has an axis of rotation that is set horizontally, pointing north. Unlike a magnetic compass, it does not seek north. When being used in an airliner, for example, it will slowly drift away from north and will need to be reoriented periodically, using a magnetic compass as a reference.
Unlike a directional gyro or heading indicator, a gyrocompass seeks north. It detects the rotation of the Earth about its axis and seeks the true north, rather than the magnetic north. Gyrocompasses usually have built-in damping to prevent overshoot when re-calibrating from sudden movement.
By determining an object's acceleration and integrating over time, the velocity of the object can be calculated. Integrating again, position can be determined. The simplest accelerometer is a weight that is free to move horizontally, which is attached to a spring and a device to measure the tension in the spring. This can be improved by introducing a counteracting force to push the weight back and to measure the force needed to prevent the weight from moving. A more complicated design consists of a gyroscope with a weight on one of the axes. The device will react to the force generated by the weight when it is accelerated, by integrating that force to produce a velocity.
A gyrostat consists of a massive flywheel concealed in a solid casing. Its behaviour on a table, or with various modes of suspension or support, serves to illustrate the curious reversal of the ordinary laws of static equilibrium due to the gyrostatic behaviour of the interior invisible flywheel when rotated rapidly. The first gyrostat was designed by Lord Kelvin to illustrate the more complicated state of motion of a spinning body when free to wander about on a horizontal plane, like a top spun on the pavement, or a bicycle on the road. Kelvin also made use of gyrostats to develop mechanical theories of the elasticity of matter and of the ether.. In modern continuum mechanics there is a variety of these models, based on ideas of Lord Kelvin. They represent a specific type of Cosserat theories (suggested for the first time by Eugène Cosserat and François Cosserat), which can be used for description of artificially made smart materials as well as of other complex media. One of them, so-called Kelvin's medium, has the same equations as magnetic insulators near the state of magnetic saturation in the approximation of quasimagnetostatics .
In modern times, the gyrostat concept is used in the design of attitude control systems for orbiting spacecraft and satellites. For instance, the Mir space station had three pairs of internally mounted flywheels known as gyrodynes or control moment gyros.
In physics, there are several systems whose dynamical equations resemble the equations of motion of a gyrostat. Examples include a solid body with a cavity filled with an inviscid, incompressible, homogeneous liquid, the static equilibrium configuration of a stressed elastic rod in elastica theory, the polarization dynamics of a light pulse propagating through a nonlinear medium, the Lorenz system in chaos theory, and the motion of an ion in a Penning trap mass spectrometer.
The hemispherical resonator gyroscope (HRG), also called wine-glass gyroscope[contradictory] or mushroom gyro, makes using a thin solid-state hemispherical shell, anchored by a thick stem. This shell is driven to a flexural resonance by electrostatic forces generated by electrodes which are deposited directly onto separate fused-quartz structures that surround the shell. Gyroscopic effect is obtained from the inertial property of the flexural standing waves.
VSG or CVGEdit
A vibrating structure gyroscope (VSG), also called a Coriolis vibratory gyroscope (CVG), uses a resonator made of different metallic alloys. It takes a position between the low-accuracy, low-cost MEMS gyroscope and the higher-accuracy and higher-cost fiber optic gyroscope. Accuracy parameters are increased by using low-intrinsic damping materials, resonator vacuumization, and digital electronics to reduce temperature dependent drift and instability of control signals.
A dynamically tuned gyroscope (DTG) is a rotor suspended by a universal joint with flexure pivots. The flexure spring stiffness is independent of spin rate. However, the dynamic inertia (from the gyroscopic reaction effect) from the gimbal provides negative spring stiffness proportional to the square of the spin speed (Howe and Savet, 1964; Lawrence, 1998). Therefore, at a particular speed, called the tuning speed, the two moments cancel each other, freeing the rotor from torque, a necessary condition for an ideal gyroscope.
Ring laser gyroscopeEdit
A ring laser gyroscope relies on the Sagnac effect to measure rotation by measuring the shifting interference pattern of a beam split into two halves, as the two halves move around the ring in opposite directions.
When the Boeing 757-200 entered service in 1983, it was equipped with the first suitable ring laser gyroscope. This gyroscope took many years to develop, and the experimental models went through many changes before it was deemed ready for production by the engineers and managers of Honeywell and Boeing. It was an outcome of the competition with mechanical gyroscopes, which kept improving. The reason Honeywell, of all companies, chose to develop the laser gyro was that they were the only one that didn't have a successful line of mechanical gyroscopes, so they wouldn't be competing against themselves. The first problem they had to solve was that with laser gyros rotations below a certain minimum could not be detected at all, due to a problem called "lock-in", whereby the two beams act like coupled oscillators and pull each other's frequencies toward convergence and therefore zero output. The solution was to shake the gyro rapidly so that it never settled into lock-in. Paradoxically, too regular of a dithering motion produced an accumulation of short periods of lock-in when the device was at rest at the extremities of its shaking motion. This was cured by applying a random white noise to the vibration. The material of the block was also changed from quartz to a new glass ceramic Cer-Vit, made by Owens Corning, because of helium leaks.
Fiber optic gyroscopeEdit
A fiber optic gyroscope also uses the interference of light to detect mechanical rotation. The two halves of the split beam travel in opposite directions in a coil of fiber optic cable as long as 5 km. Like the ring laser gyroscope, it makes use of the Sagnac effect.
A London moment gyroscope relies on the quantum-mechanical phenomenon, whereby a spinning superconductor generates a magnetic field whose axis lines up exactly with the spin axis of the gyroscopic rotor. A magnetometer determines the orientation of the generated field, which is interpolated to determine the axis of rotation. Gyroscopes of this type can be extremely accurate and stable. For example, those used in the Gravity Probe B experiment measured changes in gyroscope spin axis orientation to better than 0.5 milliarcseconds (1.4×10−7 degrees, or about ×10−9 radians) over a one-year period. 2.4 This is equivalent to an angular separation the width of a human hair viewed from 32 kilometers (20 mi) away.
The GP-B gyro consists of a nearly-perfect spherical rotating mass made of fused quartz, which provides a dielectric support for a thin layer of niobium superconducting material. To eliminate friction found in conventional bearings, the rotor assembly is centered by the electric field from six electrodes. After the initial spin-up by a jet of helium which brings the rotor to 4,000 RPM, the polished gyroscope housing is evacuated to an ultra-high vacuum to further reduce drag on the rotor. Provided the suspension electronics remain powered, the extreme rotational symmetry, lack of friction, and low drag will allow the angular momentum of the rotor to keep it spinning for about 15,000 years.
A sensitive DC SQUID that can discriminate changes as small as one quantum, or about 2 ×10−15 Wb, is used to monitor the gyroscope. A precession, or tilt, in the orientation of the rotor causes the London moment magnetic field to shift relative to the housing. The moving field passes through a superconducting pickup loop fixed to the housing, inducing a small electric current. The current produces a voltage across a shunt resistance, which is resolved to spherical coordinates by a microprocessor. The system is designed to minimize Lorentz torque on the rotor.
In addition to being used in compasses, aircraft, computer pointing devices, etc., gyroscopes have been introduced into consumer electronics. The first usage or application of gyroscope in consumer electronics was popularized by Steve Jobs in Apple iPhone.
Since the gyroscope allows the calculation of orientation and rotation, designers have incorporated them into modern technology. The integration of the gyroscope has allowed for more accurate recognition of movement within a 3D space than the previous lone accelerometer within a number of smartphones. Gyroscopes in consumer electronics are frequently combined with accelerometers (acceleration sensors) for more robust direction- and motion-sensing. Examples of such applications include smartphones such as the Samsung Galaxy Note 4, HTC Titan, Nexus 5, iPhone 5s, Nokia 808 PureView and Sony Xperia, game console peripherals such as the PlayStation 3 controller and the Wii Remote, and virtual reality sets such as the Oculus Rift.
Nintendo has integrated a gyroscope into the Wii console's Wii Remote controller by an additional piece of hardware called "Wii MotionPlus". It is also included in the 3DS and the Wii U GamePad, which detects movement when turning.
Cruise ships use gyroscopes to level motion-sensitive devices such as self-leveling pool tables.
An electric powered flywheel gyroscope inserted in a bicycle wheel is being sold as a training wheel alternative. 
- Anti-rolling gyro
- Attitude indicator
- Balancing machine
- Euler angles
- Eric Laithwaite
- Gyro monorail
- Gyroscopic exercise tool
- Inertial measurement unit
- Molecular gyroscope
- Reaction wheel
- Rigid body dynamics
- Turn and bank indicator
- Turn coordinator
- "Gyroscope". Oxford Dictionaries. Archived from the original on 5 May 2015. Retrieved 4 May 2015.
- "Gyroscope Archived 30 April 2008 at the Wayback Machine." by Sándor Kabai, Wolfram Demonstrations Project.
- Tao W, Liu T, Zheng R, Feng H. Gait Analysis Using Wearable Sensors. Sensors (Basel, Switzerland). 2012;12(2):2255-2283. doi:10.3390/s120202255.
- "20 things you didn't know about tunnels". Discover. 29 April 2009. Archived from the original on 15 June 2009.
- Range, Shannon K'doah; Mullins, Jennifer. "Brief History of Gyroscopes". Archived from the original on 2015-07-10.
- Johann G. F. Bohnenberger (1817) "Beschreibung einer Maschine zur Erläuterung der Gesetze der Umdrehung der Erde um ihre Axe, und der Veränderung der Lage der letzteren" (Description of a machine for the explanation of the laws of rotation of the Earth around its axis, and of the change of the orientation of the latter), Tübinger Blätter für Naturwissenschaften und Arzneikunde Archived 19 July 2011 at the Wayback Machine., vol. 3, pages 72–83.
- The French mathematician Poisson mentions Bohnenberger's machine as early as 1813: Simeon-Denis Poisson (1813) "Mémoire sur un cas particulier du mouvement de rotation des corps pesans" [Memoir on a special case of rotational movement of massive bodies], Journal de l'École Polytechnique, vol. 9, pages 247–262. Available online at: Ion.org Archived 19 July 2011 at the Wayback Machine.
- A photograph of Bohnenberger's instrument is available on-line here: Ion.org Archived 28 September 2007 at the Wayback Machine. ION Museum: The Machine of Bohnenberger .
- Walter R. Johnson (January 1832). "Description of an apparatus called the rotascope for exhibiting several phenomena and illustrating certain laws of rotary motion" Archived 19 August 2016 at the Wayback Machine., The American Journal of Science and Art, 1st series, vol. 21, no. 2, pages 265–280.
- Drawings of Walter R. Johnson's gyroscope ("rotascope") were used to illustrate phenomena in the following lecture: E.S. Snell (1856) "On planetary disturbances," Archived 19 August 2016 at the Wayback Machine. Board of Regents, Tenth Annual Report of the Board of Regents of the Smithsonian Institution.... (Washington, D.C.: Cornelius Wendell, 1856), pages 175–190.
- "Archived copy". Archived from the original on 28 September 2007. Retrieved 24 May 2007.
- L. Foucault (1852) "Sur les phénomènes d’orientation des corps tournants entraînés par un axe fixe à la surface de la terre — Nouveaux signes sensibles du mouvement diurne" (On the phenomena of the orientation of rotating bodies carried along by an axis fixed to the surface of the earth — New perceptible signs of the daily movement), Comptes rendus hebdomadaires des séances de l’Académie des Sciences (Paris), vol. 35, pages 424–427. Available on-line (in French): Gallica.bnf.fr Archived 16 July 2012 at the Wayback Machine.
- Circa 1852, Friedrich Fessel, a German mechanic and former secondary school teacher, independently developed a gyroscope. See: (1) Julius Plücker (September 1853) "Über die Fessel'sche rotationsmachine", Annalen der Physik, vol. 166, no. 9, pages 174–177; (2) Julius Plücker (October 1853) "Noch ein wort über die Fessel'sche rotationsmachine", Annalen der Physik, vol. 166, no. 10, pages 348–351; (3) Charles Wheatstone (1864) "On Fessel's gyroscope" Archived 19 August 2016 at the Wayback Machine., Proceedings of the Royal Society of London, vol. 7, pages 43–48.
- L. Foucault (1852) Comptes rendus..., vol. 35, page 427.
- Hermann Anschütz-Kaempfe and Friedrich von Schirach, "Kreiselapparat" (Gyroscope) Deutsches Reichspatent no. 182855 (filed: 27 March 1904 ; issued: 2 April 1907).
- MacKenzie, Donald. Inventing Accuracy: A Historical Sociology of Nuclear Missile Guidance. Cambridge: MIT Press, 1990. pp. 31–40. ISBN 0-262-13258-3
- Anon. "TEDCO Toys - Cool company history, great science kits". TEDCO Toys company website. O'Reilly Media Inc. Archived from the original on 9 March 2009. Retrieved 23 December 2010.
- MacKenzie, Donald. Inventing Accuracy: A Historical Sociology of Nuclear Missile Guidance. Cambridge: MIT Press, 1990. pp. 40-42. ISBN 0-262-13258-3
- The Little Top That Aims a Gun Archived 10 July 2011 at the Wayback Machine. by Gold Sanders, Popular Science, July 1945
- Magazines, Hearst (1 March 1954). "Popular Mechanics". Hearst Magazines. Archived from the original on 2 February 2017. Retrieved 5 November 2017 – via Google Books.
- Feynman, Gottlieb & Leighton 2013, pp. 148-149.
- "iPad - Compare Models". Apple. Archived from the original on 24 October 2012.
- "iPhone 4 Gyroscope Teardown". 24 June 2010. Archived from the original on 24 November 2011.
- Kelon, Leo (9 September 2014). "Smartwatches: Specs and reviews for the leading models". Technology. BBC News. Archived from the original on 28 August 2015.
- "Basic Sensors in iOS". Archived from the original on 23 July 2015.
- "Archived copy". Archived from the original on 23 July 2015. Retrieved 23 July 2015.
- Brown, Garrett. "Return of the Jedi", American Cinematographer, June 1983.
- Empire of Dreams: The Story of the Star Wars Trilogy Star Wars Trilogy Box Set DVD documentary, 
- Feynman, Gottlieb & Leighton 2013, pp. 115-135.
- Feynman, Gottlieb & Leighton 2013, pp. 131-135.
- William Thomson (1875). Proc. London Math. Soc., vol. 6, pages 190–194.
- Andrew Gray (1979). A Treatise on Gyrostatics and Rotational Motion: Theory and Applications (Dover, New York)
- Robert Kargon, Peter Achinstein, Baron William Thomson Kelvin: "Kelvin's Baltimore Lectures and Modern Theoretical Physics: Historical and Philosophical Perspectives" The MIT Press, 1987, ISBN 978-0-262-11117-1
- E. Grekova, P. Zhilin (2001). Journal of elasticity, Springer, vol. 64, pages 29–70
- Peter C. Hughes (2004). Spacecraft Attitude Dynamics ISBN 0-486-43925-9
- D. M. Harland (1997) The MIR Space Station (Wiley); D. M. Harland (2005) The Story of Space Station MIR (Springer).
- C. Tong (2009). American Journal of Physics vol. 77, pages 526–537
- N.N. Moiseyev and V.V. Rumyantsev (1968). Dynamic Stability of Bodies Containing Fluid (Springer, New York)
- Joseph Larmor (1884). Proc. London Math. Soc. vol. 15, pages 170–184
- M.V. Tratnik and J.E. Sipe (1987). Physical Review A vol. 35, pages 2965–2975
- A.B. Gluhovsky (1982). Soviet Physics Doklady vol. 27, pages 823–825
- S. Eliseev et al. (2011). Physical Review Letters vol. 107, paper 152501
- H. Sternberg; C. Schwalm (2007). "Qualification Process for MEMS Gyroscopes for the Use in Navigation Systems" (PDF). International Society for Photogrammetry and Remote Sensing Proceedings. Archived from the original (PDF) on 2 October 2011.
- Ash, M E; Trainor, C V; Elliott, R D; Borenstein, J T; Kourepenis, A S; Ward, P A; Weinberg, M S (14–15 September 1999). "Micromechanical inertial sensor development at Draper Laboratory with recent test results". Symposium Gyro Technology Proceedings. Archived from the original on 23 August 2012.
- Lynch, D.D.: HRG development at Delco, Litton, and Northrop Grumman. In: Proceedings of Anniversary Workshop on Solid-State Gyroscopy, 19–21 May 2008. Yalta, Ukraine. Kyiv-Kharkiv. ATS of Ukraine, ISBN 978-976-0-25248-5 (2009)
- Sarapuloff S.A. High-Q Sapphire Resonator of Solid-State Gyroscope CRG-1 glass or from single-crystalline sapphire.[dead link]
- David May (1999). "Modeling the dynamically tuned gyroscope in support of high-bandwidth capture loop design". Proc. SPIE. 3692: 101–111. doi:10.1117/12.352852.[permanent dead link]
- Donald MacKenzie, Knowing Machines: Essays in Technical Change, MIT Press, 1996, Chapter 4: From the Luminiferous Ether to the Boeing 757
- Hervé Lefèvre, The Fiber-Optic Gyroscope, 1993, Artech House Optoelectronics Library, 1993, ISBN 0-89006-537-3
- Einstein.stanford.edu Archived 14 May 2011 at the Wayback Machine.. "The GP-B instrument is designed to measure changes in gyroscope spin axis orientation to better than 0.5 milliarcseconds (1.4x10-7 degrees) over a one-year period"
- "Gravity Probe B – Extraordinary Technologies" (PDF). Archived (PDF) from the original on 27 May 2010.
- "Gravity Probe B — Extraordinary Technologies". Einstein.stanford.edu. Archived from the original on 14 May 2011. Retrieved 5 November 2017.
- Kobayashi, Takeshi; Hayakawa, Hisao; Tonouchi, Masayoshi. Vortex Electronics and SQUIDs. Google Books. pp. 44–45. Archived from the original on 4 September 2015.
- "DC electrostatic gyro suspension system for the Gravity Probe B experiment". ResearchGate. Archived from the original on 5 July 2015.
- "Samsung Galaxy and Gear - The Official Samsung Galaxy Site". The Official Samsung Galaxy Site. Archived from the original on 16 December 2014.
- "HTC Titan Specifications and Features - Techstic". 18 October 2011. Archived from the original on 3 October 2012.
- "Nexus 5 vs iPhone 5s: Head-to-head - SiliconANGLE". Siliconangle.com. 1 November 2013. Archived from the original on 13 December 2013. Retrieved 5 November 2017.
- "Nokia 808 PureView - Full phone specifications". Gsmarena.com. Archived from the original on 20 March 2012.
- "Blog — Building a Sensor for Low Latency VR". Oculus.com. Archived from the original on 8 March 2015. Retrieved 5 November 2017.
- Frank Caron (Aug 2008). Of gyroscopes and gaming: the tech behind the Wii MotionPlus Archived 15 April 2012 at the Wayback Machine., ars technica
- Adams, Paul. "Internal Gyroscope Is the Future of Training Wheels". Popular Science. Archived from the original on 27 July 2016. Retrieved 18 October 2017.
- Feynman, Richard; Gottlieb, Michael; Leighton, Ralph (2013). Feynman's Tips on Physics, A Problem-Solving Supplement to the Feynman Lectures on Physics. Basic Books.
- Felix Klein and Arnold Sommerfeld, "Über die Theorie des Kreisels" (Tr., About the theory of the gyroscope). Leipzig, Berlin, B.G. Teubner, 1898–1914. 4 v. illus. 25 cm.
- Audin, M. Spinning Tops: A Course on Integrable Systems. New York: Cambridge University Press, 1996.
- Crabtree, H. "An Elementary Treatment of the Theory of Spinning Tops and Gyroscopic Motion". Longman, Green and C), 1909. Reprinted by Michigan Historical Reprint Series.
- Proceedings of Anniversary Workshop on Solid-State Gyroscopy, 19–21 May 2008. Yalta, Ukraine. Kyiv-Kharkiv. ATS of Ukraine, ISBN 978-976-0-25248-5 (2009)
- E. Leimanis (1965). The General Problem of the Motion of Coupled Rigid Bodies about a Fixed Point. (Springer, New York).
- Perry J. "Spinning Tops". London Society for Promoting Christian Knowledge, 1870. Reprinted by Project Gutemberg ebook, 2010.
- Walter Wrigley, Walter M. Hollister, and William G. Denhard (1969). Gyroscopic Theory, Design, and Instrumentation. (MIT Press, Cambridge, MA).
- Provatidis, C. G. (2012). Revisiting the Spinning Top, International Journal of Materials and Mechanical Engineering, Vol. 1, No. 4, pp. 71–88, open access at Ijm-me.org (ISSN Online: 2164-280X, ISSN Print: 2162-0695).
|Wikibooks has a book on the topic of: High School Physics/Rotational Motion|
- The Royal Institution's 1974–75 Christmas Lecture Professor Eric Laithwaite
- One-Wheeled Robot-Gyrostat by Olga Kapustina and Yuri Martynenko Wolfram Demonstrations Project
- The Little Top That Aims a Gun by Gold Sanders, Popular Science July 1945
- Apostolyuk V. Theory and Design of Micromechanical Vibratory Gyroscopes