Electromagnetic forming (EM forming or magneforming) is a type of high velocity, cold forming process for electrically conductive metals, most commonly copper and aluminium. The workpiece is reshaped by high intensity pulsed magnetic fields that induce a current in the workpiece and a corresponding repulsive magnetic field, rapidly repelling portions of the workpiece. The workpiece can be reshaped without any contact from a tool, although in some instances the piece may be pressed against a die or former. The technique is sometimes called high velocity forming or electromagnetic pulse technology.
A special coil is placed near the metallic workpiece, replacing the pusher in traditional forming. When the system releases its intense magnetic pulse , the coil generates a magnetic field which in turn accelerates the workpiece to hyper speed[quantify] and onto the die. The magnetic pulse and the extreme deformation speed transforms the metal into a visco-plastic state – increasing formability without affecting the native strength of the material. See the magnetic pulse forming illustration for a visualization.
A rapidly changing magnetic field induces a circulating electric current within a nearby conductor through electromagnetic induction. The induced current creates a corresponding magnetic field around the conductor (see Pinch (plasma physics)). Because of Lenz's Law, the magnetic fields created within the conductor and work coil strongly repel each other.
In practice the metal workpiece to be fabricated is placed in proximity to a heavily constructed coil of wire (called the work coil). A huge pulse of current is forced through the work coil by rapidly discharging a high voltage capacitor bank using an ignitron or a spark gap as a switch. This creates a rapidly oscillating, ultrastrong electromagnetic field around the work coil.
The high work coil current (typically tens or hundreds of thousands of amperes) creates ultrastrong magnetic forces that easily overcome the yield strength of the metal work piece, causing permanent deformation. The metal forming process occurs extremely quickly (typically tens of microseconds) and, because of the large forces, portions of the workpiece undergo high acceleration reaching velocities of up to 300 m/s.
The forming process is most often used to shrink or expand cylindrical tubing, but it can also form sheet metal by repelling the work piece onto a shaped die at a high velocity. High-quality joints can be formed, either by electromagnetic pulse crimping with a mechanical interlock or by electromagnetic pulse welding with a true metallurgical weld. Since the forming operation involves high acceleration and deceleration, mass of the work piece plays a critical role during the forming process. The process works best with good electrical conductors such as copper or aluminum, but it can be adapted to work with poorer conductors such as steel.
Comparison with Mechanical FormingEdit
Electromagnetic forming has a number of advantages and disadvantages compared to conventional mechanical forming techniques.
Some of the advantages are;
- Improved formability (the amount of stretch available without tearing)
- Wrinkling can be greatly suppressed
- Forming can be combined with joining and assembling with dissimilar components including glass, plastic, composites and other metals.
- Close tolerances are possible as springback can be significantly reduced.
- Single sided dies are sufficient which can reduce tooling costs
- Lubricants are reduced or are unnecessary, so forming can be used in clean room conditions
- Mechanical contact with the workpiece is not required, this avoids surface contamination and tooling marks. As a result, a surface finish can be applied to the workpiece before forming.
The principle disadvantages are;
- Non conductive materials cannot be formed directly, but can be formed using a conductive drive plate
- The high voltages and currents involved require careful safety considerations
- "Materials and Manufacturing: Electromagnetic Forming of Aluminum Sheet" (PDF). Pacific Northwest National Laboratory. Archived from the original (PDF) on 2005-12-18. Retrieved 2006-06-09.
- "Electromagnetic Hemming Machine And Method For Joining Sheet Metal Layers". US Patent and Trademark Office. Retrieved 2005-09-02.[permanent dead link]
- "Resources on Electromagnetic and High Velocity Forming". Department of Materials Science and Engineering, Ohio State University. Archived from the original on 2005-12-19. Retrieved 2006-04-06.
- "Electromagnetic Metal Forming Handbook". An English translation of the Russian book by Belyy, Fertik, and Khimenko. Archived from the original on 2006-09-05. Retrieved 2006-08-06.
- "FEA of electromagnetic forming using a new coupling algorithm". Ali M. Abdelhafeez, M.M. Nemat-Alla and M.G. El-Sebaie. Retrieved 2013-01-15.
- "Industrial Application of the Electromagnetic Pulse Technology" (PDF). PSTproducts GmbH. Archived from the original (PDF) on 2011-07-15. Retrieved 2010-08-01.
- "Electromagnetic Forming of Cylindrical Components". Magnet-Physik. Archived from the original on 2005-12-14. Retrieved 2006-06-06.