Connectors for car audio

Several types of connectors for car audio systems are used.

Splicing wiresEdit

Splicing wires used in car audio are mainly for power, ground, amplifier and antenna, speakers, phone and others.

Power and groundEdit

  • ACC (red), supplies +12V power to car audio and other accessories, only when the car's ignition is switched on.
  • Constant (yellow), also called BAT or Battery, provides permanent +12V power from battery. This allows the radio to retain settings (for example stored radio stations) when the ignition is switched off.
  • Illumination (orange with white stripe) or dimmer, when it is night and cars lights are turned on, head unit screen illumination is dimmed.
  • Ground, abbrev. as GND (black), 0V, usually connected to the vehicle's metal chassis and body.


Wires with black stripe are for negative power:

  • Right front speaker: gray.
  • Left front speaker: white.
  • Right rear: purple.
  • Left rear: green.

Amplifier and AntennaEdit

They have low amperage and it is activated when radio is turned on.

  • Antenna: blue.
  • Amplifier remote turn on: blue with white stripe.

Phone And OthersEdit

  • Phone : the cable to mute when receiving a call, is brown.
  • Back view, orange with white strip, works when reverse gear light is on and it is used to turn on back camera screen (i.e. when parking).
  • Steering Wheel Controls, SWC or Key, brown with black stripe, usually employs CAN bus.

ISO 10487 Harness AdapterEdit

ISO 10487 connector in car, fits into head unit

ISO 10487 was created in 1995 and defines a standard for connectors for the head unit to the car's electrical system, consisting of a system of four different connectors typically used in head units for car audio.

ISO 10487 connector pinout (plug side of male, wiring side of female)


Part 1 of the standard is dedicated to "Dimensions and general requirements" and Part 2 to "Performance requirements".

Power (A)Edit

The first connector A is always present, is usually black in colour, and contains pins for power-supply, off/on (typically controlled by ignition key), optional control for a motorised antenna and so on.

  • On some cars the +12V Ignition and Battery positions are reversed, such as later Volkswagen Group cars, Peugeot 106, Vauxhall Astra, Citroën C3 and some JCB tractors.
  • Pin 1 is optional; used for speed dependent volume control and possibly navigation.
  • Pin 2 is optional; used for phone mute
  • Pin 3 is optional; used for reversing lamp signal on Becker radios with navigation.
  • Pin 6 is optional; used for vehicle instrument illumination

Loudspeaker (B)Edit

The second connector B is for connecting four loudspeakers, front, rear, left and right, and is usually brown in colour.

Miscellaneous (C)Edit

The connector C is optional. Sometimes it appears as one 20-pin connector, often red in colour, or it may be divided into three separate connectors which may be hooked together, in which case C1 is usually yellow, C2 is usually green and C3 is usually blue in colour. The contact spacing is narrower than the other connectors, so the C connector is sometimes referred to as mini-ISO.

C1 (external amplifier)
1) line out left rear 4) line out left front
3) line out common ground 6) +12V switched (out)
2) line out right rear 5) line out right front
C2 (remote control)
7) receive data 10) +12V switched (out)
9) chassis ground 12) remote control ground
8) transmit data 11) remote control in
C3 (CD changer)
13) data in (bus) 16) +12v switched (out) 19) audio left
15) +12v permanent (out) 18) audio ground
14) data out 17) data ground 20) audio right

Note: ISO 10487 only defines the physical attributes of the connectors, not the pin/signal designations, which are manufacturer-defined. The example above is oriented towards VW vehicles only.

Navigation (D)Edit

The connector D is for satellite navigation systems. It has 10 pins.


From 2000 and onwards, manufacturers, such as BMW, Citroën, Ford, Mercedes Benz, Peugeot, Volkswagen, Rover, Audi, SEAT, Opel or Škoda have sometimes started using a 40-pin connector instead, called the Quadlock.

Unfortunately, Quadlock may not be the description used by manufacturers of the connector components. Therefore, searching for Quadlock components may be unsuccessful; for example, Molex refer to a typical component of the connector as MOST Frame Receptacle Housing (part number 986811001) .

The Quadlock connector consists of a block of 16 flat pins analogous to the two main ISO 10487 connectors.[1] While the physical contact pins are the same, the pin allocation is not entirely the same, and the connector housing is not compatible. In addition to the 16 pins, like ISO 10487, there are minor connectors for optional equipment. They fit within the frame of the main connector, and has coding so that they cannot be interchanged. Minor connector B has 12 pins for audio output signals. Minor connector C has 12 pins for various audio sources such as CD-changers, MP3 players.

Quadlock A
1) right rear + 5) right rear - 9) I-bus (BMW) / CAN High 13) antenna (out)
2) right front + 6) right front - 10) phone mute / (Speed Signal) 14) illumination
3) left front + 7) left front - 11) tel on / CAN Low 15) 12V battery
4) left rear + 8) left rear - 12) ground 16) 12V switched

See alsoEdit


  1. ^ "Quadlock pinout". PinoutGuide.

External linksEdit