The Belle of Oregon City, generally referred to as Belle, was built in 1853, and was the first iron steamboat built on the west coast of North America.[3]

Advertisement for steamers Belle and Mary, February 17, 1855
History
NameBelle of Oregon City
OwnerWells and Williams; Oregon Steam Navigation Company[1]
Port of registry[1]
Routelower Columbia River, lower Willamette River
BuilderWilliam H. Troup and ironworks of Thomas V. Smith[3][2]
LaunchedAugust 18, 1853, Linn City, Oregon[1][2]
In service1853
Out of service1869
FateDismantled 1869, engines salvaged[1]
NotesFirst iron vessel built in Oregon or the Washington Territory; first steam vessel with Oregon-built equipment.[3]
General characteristics
Typeshallow draft inland passenger/freight, iron hull[3]
Tonnage54 gross[3]
Length90 ft (27 m) on keel; 96 ft (29 m) measured over guards[1][3]
Beam16 ft (5 m)[2][4]
Depth4.0 ft (1 m) depth of hold[1]
Installed powersteam engine
Propulsionsidewheels

Design and construction edit

Belle was also the first steamboat to be powered by machinery built entirely in Oregon. All the iron and all the required machinery, including the boiler and steam engines, was produced by foundryman Thomas V. Smith in his ironworks at Oregon City.

Capt. William H. Troup built the vessel for two other men, Capt. William B. Wells and Capt. Richard Williams.. Because of her iron hull, she was much more durable than most early Oregon steamboats, lasting until 1869. Belle measured 90 ft (27 m) on her keel and 96 ft (29 m) measured over her guards.[3]

Operations edit

 
William B. Wells (1822-1863), co-owner and captain of Belle of Oregon City

Williams and Wells first used Belle on the Willamette River run between Portland and Oregon City, with passenger fares $2 each way. The boat departed the base at Willamette Falls at 7:30 a.m., was at the Oregon City dock by 8:00 a.m., stopping at Milwaukie at 8:30 a.m., and reached Portland at 9:30 a.m.

At 2:00 p.m. Belle steamed back upriver, reaching the falls by 4:00 p.m. (Because of a stretch of shallow water on the Willamette near the mouth of the Clackamas River known as the Clackamas Rapids, only smaller vessels could make this run.) Belle also ran on the Cowlitz River and to Fort Vancouver.[3]

By July 1855, Belle was on the route from Portland down the Willamette and then also ran up the Columbia to the lower Cascades, making three runs a week, under Captain Wells, with J.M. Gilman as engineer and N.B. Ingalls as purser. (Ingalls would become one of the longest-serving pursers on the Columbia River, serving on many of the river steamers from the 1850s to his retirement in 1893).

Passengers headed up river would disembark at the lower Cascades, travel on the portage road along the north bank, and then board the sidewheeler Mary upriver to the next head of navigation, The Dalles. Freight charges were high, $50 a ton on cargo from Portland to The Dalles, but Belle and Mary still could not handle the demand, and other steamers came on the routes, driving rates down to $30 a ton.[3][2][5]

Military transport edit

 
Brevet Lt. Philip Sheridan

In the 1850s, the U.S. Army was engaged in forcing the First Nations to cede their dominion over the vast lands of the Oregon and Washington Territories and move onto reservations.

The army maintained posts at Fort Vancouver, the Cascades, and The Dalles. In late 1855 orders arrived to move the army's main base up from the Cascades to the Dalles, closer to the anticipated area of war operations in the next campaign season. Movement on the river was completely halted by the severe winter in January 1856, when the Columbia froze from bank to bank from the Gorge on down well below the mouth of the Willamette. No river traffic moved anywhere on the river, even down to Astoria, Oregon. When the river was finally clear enough of ice, Belle and another boat, the Fashion started moving the Army's equipment up from Fort Vancouver.[3]

On March 26, 1856, a war party of the First Nations attacked the town at Upper Cascades, burned most of the buildings, and laid siege to the blockhouse at Fort Cascades, killing 11 civilians and 3 soldiers. Word soon reached Fort Vancouver, where Lt. (later Genl.) Philip H. Sheridan loaded his troopers on Belle and steamed upriver to the Cascades. Meanwhile, other troops were coming downriver on Mary from The Dalles, and arrived at Upper Cascades.

There was some fighting for a few days around the lower Cascades, during which Belle acted as ammunition and supply transport. Due to military blunders the troops were not able to trap the First Nations war party at the Upper Cascades; they slipped back into the forest.[3]

Later years of service edit

When the Oregon Steam Navigation Company was formed, Belle was absorbed into the monopoly and became part of O.S.N.'s near-absolute dominance of Columbia River steam navigation, but was little used by the new company. Her sturdy construction still allowed her to outlast most of the steamboats built on the Willamette and Columbia Rivers in the 1850s and 1860s. Belle was scrapped in 1869, her hull was dismantled and shipped to China, and her engines went to power a sawmill at Oak Point.[3][2]

Notes edit

  1. ^ a b c d e f Affleck, Edward L., A Century of Paddlewheelers in the Pacific Northwest, the Yukon, and Alaska, Alexander Nicholls Press, Vancouver, BC 2000 ISBN 0-920034-08-X
  2. ^ a b c d e Wright, E.W. ed,, Lewis & Dryden Marine History of the Pacific Northwest, at 43-44 , Lewis & Dryden Printing Co., Portland, OR 1895
  3. ^ a b c d e f g h i j k l Mills, Randall V., Sternwheelers up Columbia – A Century of Steamboating in the Oregon Country, Univ. of Nebraska, Lincoln, NE (1977 reprint of 1947 ed.). pp. 25-26, 31-40,165, 170, 190. ISBN 0-8032-5874-7
  4. ^ Mills gives beam as 26 ft (8 m)
  5. ^ Timmen, Fritz, Blow for the Landing – A Hundred Years of Steam Navigation on the Waters of the West, Caxton Printers, Caldwell, ID (1973). pp. 8, 14, 72-73. ISBN 0-87004-221-1

Further references edit